How to set up a security setting on my WBR-1310 D-Link router

First you will need to find the local IP address of your router. It should look something like "192.168.0.1" You might be able to find it in either your router manual or on the bottom of the router itself.
Then make sure your computer is connected to the router via wireless or ethernet cable.
Next, open your browser and type in the IP address into the address bar. It should take you to a setup page that looks a lot like a website. Find the "wireless security" tab and select a security protocol. I recommend using either WPA or WPA2. Now you can set a password. Finally, there should be "save" button on the page. Click it, then wait for your router to reboot and your network is now secure.

Use the PING command to test the communication between the computer and the gateway.

Goto Start > Run and enter COMMAND.
From the Command Prompt, enter PING 192.168.0.1.
The gateway should reply.

Verify that the residential gateway is getting power. With the broadband modem connected to the WAN port on the gateway, you should have a soild WAN link light. You should use the same cable that connected the modem to the PC to connect the modem to the WAN port on the gateway. Any port on the gateway that has a computer connected to it should have the corresponding LAN link light lit. If you do not get the appropriate link lights, try using different cables.

onfigure browser/Internet Options
Step 1 Go to Start > Settings > Control Panel.

Step 2 Double-click the Internet Options icon.

Step 3 On the Security tab click Restore the default security level.

Step 4 Click the Connection tab and set the dial-up option to Never Dial a Connection.

Step 5 Click LAN Settings. Nothing should be checked. If anything is checked, uncheck it. Click OK.

Step 6 Click the Advanced tab and then click Restore these settings to their defaults.

Step 7 Click OK.

Step 1 Turn the Cable/DSL modem off.

Step 2 Turn the D-Link router off.

Step 3 Wait 60 seconds.

Step 4 Turn the cable/DSL modem back on and wait until all the lights are steady.

Step 5 Turn the D-Link router on.

Most routers and modems do not have an on/off switch. Simply unplug the power. Unplugging the power will not reset (reset back to default settings) the unit.

By going to the security setting in the router and assigning a WAP/WEP "Key" this will then enable security. Please consult your manual for how to do this.

ftp://ftp10.dlink.com/pdfs/products/WBR-1310/WBR-1310_ds.pdf
manual above

• You need to log into the router setup screen - you do this by connecting a PC to the Router via a cable connection and then using Internet Explorer (IE) you log into the router.

Using the default settings

• Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to admin and leave the password box empty. Click OK to continue.
• Goto the Wireless security section to set the security type and the password

Section 4 of the manual - see below deals with setting the wireless security This is the support site for that router http://www.dlink.com/products/?pid=WBR-1310
Click on the Support Resources - that will take you to the manuals for different Version of that model - click on the model you have to get to the online manual

theres a couple of version of this router http://www.dlink.com/products/default.aspx?pid=WBR-1310&tab=3 I'm using the manual from here http://www.dlink.com/products/?tab=3&pid=WBR-1310&rev=WBR-1310
on a working PC download and install this program http://www.xirrus.com/library/wifitools.php this will detect all the wireless signals being broadcast - see if the router is actually broadcasting - if it is detected on your PC then it may be that 1) the firewall is blocking access or 2) the security code is entered wrong - -log into the router and remove the wireless security and see if you can now detect

You can secure your wireless network wit WEP or WAP code.
For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
For belkin router http://192.168.15.1
or
http://192.168.2.1

If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Click on wireless settings then enable WEP Security then add WEP code .It is your password to connect wi fi.Then save settings and restart router.
Then you can connect your wi fi network with that code.
Thanks for using FixYa.

To secure the wireless network, you will need to access the router set up.
Is there any computer connected to the router ?
If not then you will need to connect the router to the computer .
Then check the IP address of the computer and open the router set up.
Click Here for step by step solution on how to secure the network

Try to uncheck UPnP Enable on your router located on advaced network setting. or try reconfiguring your wireless network settings.

Try creating a new wireless connection network or disable the UPnP on your WBR-1310.

Type 192.168.0.1 (you can type the router address if you have changed) and enter on browser's addressbar. Router's interface will appear.
Click on SETUP and Click on the WIRELESS SETTINGS at left side. on the page you will see the option of WIRELESS SECURITY by drop down menu you can choose the Security mode that you wish. here is the link for the emulator
http://support.dlink.com/emulators/wbr1310_revB/wireless.htm

Please post your question if you need further assistance
Good Luck