I need to find the user manual for a Hatchrite Mobel Number HR CP I-250 or HR MP I-250 incubator.

Hello,

Here are instructions from another website along with various links to download manuals and lead you to other forums talking about egg incubators:

Operating steps:
1. Put the mesh with the rail(big mesh)(fig.1) into the incubator.
2. Put the moveable egg tray (fig.2) on the mesh with rail, please do it within the rail.
3. Put the egg tray grille ( fig.3) into moveable egg tray according to size of egg for incubation.
4. Put the hatching egg into moveable egg tray(fig.5) for incubation, pay attention that after each egg is put into the grille, there should be 5mm clearance at least for convenient turning of hatching egg, inject 100ml water into the base after the hatching egg is put, check once for every two days so that the incubator is not short of water. Every water injection shall not be more than 100ml, take down the date of placing hatching egg so as to well control the hatching time. It's best to place the incubator on 60-100cm for convenient insertion of link rod.
5. When closing the cover(fig.7) , the link rod must insert the shifting slot of moveable egg tray, so that the egg tray can shift normally.( in other words, the cercley thingy coming out of the top with a rod in it has to be attached to the egg tray by putting the rod into the egg turner square hole to make sure that the incubator turns the eggs well)
6. Switch on the power supply after closing the cover, and set temperature according to push-button instruction and incubation technology. If the user has no time to care about the temperature, the temperature can be set at 38'c from the first day of hatching, and it can be set as 37.5 - 37.8C since the following day of hatching.
7. It moves to hatching tray 3 days earlier than incubation period for other poultry
8. It usually takes 3-4 days less than the number of incubation days for egg tray replacement, replace the egg tray once one or two hatching eggs are seen hatched, take all of the hatching eggs off from the incubator firstly, then take the moveable egg tray with mesh with rail out, check the water level, then put the hatching mesh( fig. 10) and egg tray in and put the hatching egg on the egg tray, shown as fig. 11.
9. After closing the cover and switching on the power supply, the hatching situation can be observed.

This was originally posted here: Janoel 12 incubator help

Best wishes,
Joe

I’m happy to help further over the phone at https://www.6ya.com/expert/mark_7bbaa7a1174e0903

Here is a link to get a dvhrso2, don't know if this is the one you need or not?

http://3wires.net/manuals/BushHVRS02.pdf

You can try this site to download a copy, however my McAfee blocked it when I tried to download it??????? You will try this at your own risk!
http://filesfromtheworld.net/casio-hr-100tm-user-manual/

You can get assistance from Sheldon Labs
Email: [email protected]
Phone: 503-640-3000 ext. 2407

http://www.backyardpoultry.com/forum3/download_vault/JN848%20user%20guide01.pdf

I need user manual for Argis IO-1P TE Incubator for Chicken

You can set the date and time on the machine:

1) Press <Fax>
2) Press <Menu>
3) Use [<] or [>] to get to "User Settings"
4) Use the number keys to enter the date (only use the last two digits of the year) and time (in 24 hr format)
5) Press <OK>
6) Press <Stop/Reset>

Your MP 530 should obtain the time from your computer when hooked up with the MP driver installed.

Yes to replace the lamp you need to remove the 2 screws. You can touch the lamp but I try not to. After the lamp is in you need to reset the hr timer for the lamp. to do this you need to look in manual on page 34.
If you do not have the manual you can get it here at link below.

http://www.aboutprojectors.com/pdf/hitachi-cp-s235-manual.pdf

Good luck

Normally most home treadmills are 250-300lb user capacity.
Call Precor with your model # and S/N and they can tell you exactly.

http://www.projectorcentral.com/pdf/projector_manual_386.pdf

your projector is the exact same as the hitachi cp-x950w/e. as a matter of fact, hitachi made the 3m mp8730.