Question about Kenmore HE2 Plus Front Load Washer

2 Answers

I have a Kenmore HE2T error code F24

I have a Kenmore HE2T washer and I keep getting an F24 error on it.. I have no idea what is means can't find the manual help!!!

Posted by scooby73000 on

Ad

2 Answers

Jeff Rockwell

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 5,911 Answers

The "F24" error code is a heat sensor error code. The following link explains the error code in detail and the steps to correct it:

http://www.fixya.com/support/r1976126-f24_error_code_whirlpool_duet_kenmore

In many cases, the connector plug on the NTC sensor wiggles loose and causes the error code. Check the NTC connection first to make sure it is tight and making good contact. This may save you a service call and/or replacement parts. Make sure you UNPLUG the washer before servicing anything inside the unit.

A replacement NTC module (if required) can be purchased at searspartsdirect.com for about $10. Refer to the parts illustrations under the "Tub and Basket Parts" heading.

If you have any questions, please let me know. I hope this helps you.

NOTE: Each washer comes with a technical data sheet located inside the cabinet. You will need to remove the lower toe panel directly below the door to access it. If it is not located directly behind the panel, it will be affixed to one of the interior cabinet walls. The tech sheet includes all troubleshooting tips, wiring diagrams and fault codes with explanations.

Posted on Dec 09, 2009

Ad

kelso43

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

When you take off your lower access panel you will find taped to the right side the manual with all the codes. This would have been nice to know. I had to figure out was an 5b was. which by the way is a clogged drain plug.

Posted on Jan 10, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F-24 error code so I ran a clean washer cycle, and the laundry room is now flooded.


what's f24 code? - Kenmore Elite HE3 Washing Machine ...

https://www.ifixit.com/Answers/View/85549/what's+f24+code

iFixitAug 21, 2015 - Aiman, The F24 error code indicates a water temperature sensor reading that is ... The Kenmore Elite HE3 is a washing machine by Kenmore.

F24 Error Code on My Kenmore Washer ' eHow

www.ehow.com > Home
F24 Error Code on My Kenmore Washer. Kenmore washing machines have several high-tech features, such as a stain treatment option, reduced energy and ...

Kenmore HE2 Plus Front Load Washer F24 error code ...

www.fixya.com > ... > HE2 > Kenmore HE2 Plus Front Load Washer
...error code F24 I have a Kenmore HE2T washer and I keep getting an F24 error on it.. I have no idea what is means can't find the manual help!!! The "F24" error ...

I have a Kenmore HE2T error code F24 - Fixya

www.fixya.com/support/t3608391-kenmore_he2t_error_code_f24
Dec 9, 2009 - Posted on Dec 09, 2009.

Dec 06, 2015 | Kenmore HE2 Plus Front Load Washer

1 Answer

I have a Kenmore HE2t i keep getting error f21 i cleaned the trap and it still does it


You may have to unplug it for about 15 minutes and try again. I had a similar problem and this helped.

Mar 19, 2014 | Kenmore HE2t 3.7 cu. ft. Front Load Washer

1 Answer

HE2T front load washer F28 flashes machine is locked clothes inside cannot open help


tre
ert
Sorry to read about your problem, I hope this helps you out.

The error code F28 means one or both of these parts are bad.
Motor Control Unit (8540135)
Microcomputer Machine Control Unit (8540788)

It would be a good idea to order both, as both components have been problematic for
error code F28

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful
2 Thumbs - Somewhat Helpful

Jan 03, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

Code F 24 what does it mean The washer dose not allow me to do anything when I push start. All the areas light up and flash with code F 24


The F24 error code indicates a problem with the water temperature sensor. code meanings should be under lower cover, remove panal.

Jul 13, 2010 | Kenmore HE2 Plus Front Load Washer

5 Answers

Kenmore HE2t washer - error code 5d


5d is a definitely a the code for a plugged discharge. We removed the lower access panel and discovered a virtual treasure: $12.50 in quarters, nickels, dimes and pennies, a pen, a pencil, collar stays, 10 bobby-pins, 3 barrettes, a elastic headband, a draw string, a box cutter, 3 washers, 3 broken zipper parts, a elastic waist band. Amazing it took all to trigger a 5d error code. Hope this helps!

Dec 05, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Kenmore he2t error code 21


F21 is a long drain...it is taking too long to drain..you have a something slowing down the drain.. you can remove the bottom panel and clean out coin trap... if there is nothing then you may have another problem... but this is the most common problem..

Sep 23, 2009 | Kenmore Washing Machines

1 Answer

Error code f24


F24 indicates a water temperature sensor error. If during the wash cycle in the water-heating step, the water temperature sensor (NTC) value is out of range the F24 error code will display.

Possible causes:
  • Too cold of water or hot water is turned off
  • Temperature sensor failure or loose connection
  • Control board failure

Dec 18, 2008 | Kenmore Washing Machines

1 Answer

F24 error code


Take off the lower panel of your washer and under this panel on the back of panel is a book which tells you what the error codes are and how to fix them or test for them. It looks like a tempature sensor code to me.

Apr 19, 2008 | Kenmore 46462 Front Load Washer

4 Answers

Fault code F20 on kenmore he2t clothes washer


I have a brand new front loader that never fill with water but shows F20. How can I get this machine to wash clothes?

Dec 29, 2007 | Washing Machines

Not finding what you are looking for?
Kenmore HE2 Plus Front Load Washer Logo

5,331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Will Mishler
Will Mishler

Level 2 Expert

307 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...