Lost manual how to progam my local channels - Uniden BC350C Base Scanner

how to program mikomi

Almost all TV makers have the manuals available for download from their web site under "support"

The 210XL and the 210XLT are nearly identical except for the number of channels, so the 210XL manual should answer any questions you have. You can download and print the manual, at no cost, here:
http://f1.grp.yahoofs.com/v1/wJJ9TdG7Qk65ge9CsRfSuB42k0iiifl8mcGykyii5QiwRK3zlwQQplAZxqlhZNnV_WVX1Yrx0R94b46AAHcoFLxBBlKrQFM/Bearcat-210xl.pdf

Bill B.
Listening in professionally since the 60's

Link below has Paragon EC7000 series timers and manuals
EC7004/120 is 7-day programmable timer.
Single channel 120Volt SPST NEMA1 indoor timer.
Program up to 16 events per week
http://waterheatertimer.org/Paragon-timers-and-manuals.html

EC7000 series programming manual shows wiring, explains keypad, has steps for setting current time, and shows 24 steps for programming timer. Plus troubleshooting.
It is impractical to write out those steps when they appear in manual.
http://waterheatertimer.org/pdf/Paragon-EC7000-04-05-manual.pdf

EC7000 series Sell sheet with model numbers
http://waterheatertimer.org/pdf/Paragon-EC7000-sell.pdf
Description of model numbers at Uni-line
http://www.uni-line.com/modules/catalog/SearchResults.aspx?catName=19030&pID=19029&mode=categorysearch

You listed your question under the BC60XLT, which is a 10-channel scanner. With 30 channels, I'm guessing that yours is actually a BC60XLT-1. To program a known frequency into it:

- Power the scanner ON.
- Press MANUAL.
- Enter the channel number that you wish to program.
- Press MANUAL again. (NOTE: Instead of entering the channel number, you can press MANUAL repeatedly to advance to the desired channel.)
- Enter the frequency, including the decimal point.
- Press E to store the information in memory.
- Repeat the above for other channels.

More detailed information can be found in the scanner operating manual, which you can download/print here:

http://www.uniden.com/pdf/BC60XLT-1om.pdf

If your scanner is a different model, pleasd let me know.

For a comprehensive database of active frequencies in your area, visit:

www.RadioReference.com

Bill B

Make sure you have fresh batteries,turn on the unit,press manual,enter the channel number,press manual,enter the frequency you want,press E enter,if you make a mistake, press CLR to erase. Get the frequency,s for your state at RadioFreq.com. ..hope this helps..

hold down code until it stays lit, then press tv then keep hitting channel up or channel down (either one can be used, keep pressing channel button til tv changes channels when it does press enter, or ok if enter is not there, it may take awhile maybe a few channel pushes up to 200 and up times, you use this method when you don't know the code for your tv. Hope this helps.

Hi,

For clarification, may I know the Brand of your remote.? There was several model to PX-RC1..

Thanks

I got this from the link below.
1- do a system reset (install > factory restore)
2- manual search
3- tp search (yellow button)
4- starts search
5- pick your local source (for me it said galway chores)
6- wait for it to get all the tp's (could take a while)
7- let it search for the channels (i found around 130)
8- sit back and enjoy

http://forums.afterdawn.com/thread_view.cfm/693531

hope this helps

Go into the menu to channel setup and change the setting from tv back to cable(catv).