Jensen A300HLX Car Audio Amplifier Logo

Related Topics:

Question about Jensen A300HLX Car Audio Amplifier

1 Answer

I have an older model Jensen 500 watt 2 channel bridgeable amp. When i hook it up the red light(protect light) comes on and it will not work

Posted by starkey_55 on

Ad

1 Answer

Professor_V

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 93 Answers

REMOVE THE RCA INPUTS AND DISCONNECT THE SPEAKERS AND POWER THE AMPLIFIER UP WITH THIS NO INPUT, NO SPEAKER LOAD CONDITION. IF IT STILL GOES INTO PROTECTION AND YOU HAVE VERIFIED THAT THE POSITIVE AND ESPECIALLY THE GROUND CONNECTIONS, ALONG WITH THE REMOTE CONNECTIONS ARE 100%, THEN THE AMPLIFIER WILL NEED TO BE SERVICED. LET ME KNOW IF YOU NEED FURTHER ASSISTANCE.....V

Posted on Jan 06, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How do i bridge all 4 channels on the jensen 400 watt 4 channel lxa amp ?

  • This amp is not "bridgeable" at all. You will either blow the front end or blow the low end voice coil in your sub.

Regards, Tony
0helpful
1answer

What fuse do i use for my Jensen 2 Channel Bridgeable Amplifier with 300 Watts Peak? thank you.

Watts = Voltage x Current

300 = 12 x Current

Current = 25 amps

Sounds like a 30 amp slo-blo fuse would be about right -- you could start with a 25 amp and see if that holds it.

Charlie
1helpful
1answer

How do i bridge my jensen 200 watt amp? its a 2 channel bridgeable.

Easy, you grab a dual wire cable (like the one in the back of your amp that runs to the speaker) and stick each wire on one end to the positives on your amp. Then, on the other end, twist both wires together to form one wire. Hook it into your positive connection on the sub(s). Repeat on negative side.


I’m happy to assist further over the phone at https://www.6ya.com/expert/pedro_4520403b21ed459a

0helpful
1answer

Red light

try runing the remot to the battery and c wat it does
0helpful
1answer

Its stuck on protected. I recieved the amp for my birthday in 2000. It protected it self 90 days later. I needed an amp righr then so I went and bought a 600 watt jensen. I took the old one out of the...

whats the ohm rating of amp probally 4 what is the ohm rating for sub how many subs are you running how do you have them hooked up parallel or series is your wiring to amp right
0helpful
1answer
1helpful
2answers

How do I fix the problem so they work again.?

A 1000 WATT AMP HAS PROBABLY GONE INTO PROTECTION MODE BECAUSE YOU ARE TRYING TO RUN 1600 WATT SUBS COMBINED
0helpful
1answer

Amp is in protect mode, green light is on.

If the amp is going into protect, it likely has shorted output transistors. To eliminate other possible causes, read through the following page.

Amp in protect mode - troubleshooting

Let me know if you have any other questions.
0helpful
1answer

600 watt 4 channel bridgeable mosfet power supply jensen amp

Swap the wires from one speaker to the other to see if it is the speaker or the Amp/wires. 

Not finding what you are looking for?

797 views

Ask a Question

Usually answered in minutes!

Top Jensen Car Audio & Video Experts

ZappaNut
ZappaNut

Level 3 Expert

960 Answers

xxxxxx xxx

Level 3 Expert

5047 Answers

The Knight
The Knight

Level 3 Expert

76851 Answers

Are you a Jensen Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...