Positive goes up on the front or back ? - Kodak Vivitar KV270 Film Camera

Car Radio Constant 12v+ Wire: Red
Car Radio Switched 12v+ Wire: Green/Black
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Yellow
Car Stereo Dimmer Wire: Black/Orange
Car Stereo Antenna Trigger: Green
Left Front Speaker Positive Wire (+): Black
Left Front Speaker Negative Wire (-): White
Right Front Speaker Positive Wire (+): Blue
Right Front Speaker Negative Wire (-): Red
Left Rear Speaker Positive Wire (+): Black
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Green
Right Rear Speaker Negative Wire (-): Orange

Here's how it goes.
Grey=right front positive
Grey/black=right front negative
White=left front positive
White/black=left front negative
Violet=right rear positive
Violet/black=right rear negative
Green=left rear positive
Green/black=left rear negative
Red=12 volt switched power (work off key)
Yellow=12 volt constant power (direct to battery)
Orange=Illumination (not dimmed by head light switch)
Black=chassis ground

The shampoo solution goes in the back container. The clean water goes in the water bag in the front section.

If you need parts you can find them below

http://www.usavacuum.com/category-s/387.htm

Make sure to give positive feed back.

Thanks. USAVACUUM.COM

Under the seat you'll see two motor driven cables, the one that goes to the front /rear track can be uncoupled from the track. Place the seat in the position you reqire and replace the cable.

Try jiggling the handle bars as you turn the key to relieve the pressure off the ignition lock. The kawasaki's have one position past the off "Lock" position that is called the "Acc" this will leave your brake light on. So the key switch goes "Acc", "Lock", "On". Make sure your key is in the Lock position and not the Accesory position

As a rule of thumb, the flat side of the needle always goes towards the opposite side of the last thread guide. So on your machine, since the last thread guide is in the front of the needle bar, the flat side of your needle goes toward the rear. The needle threads front to back.and needle clamp is tight position is must

Check the switch. It sounds like it has seen better days. Also check the wires on the back of the switch to see if they are shorting out. The problem is at the switch area. Good luck.

Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:

• It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
• The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).

• The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
• Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.

----------------------------------------------------------------------------------------------

Removal

1. Unscrew front seat head rest guide rod retainers (610A18).
   

1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
   

1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
   

Installation

1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
   

1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
   

1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
   

1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
   

1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.
   
   Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.
   

Need to replace the front panel. Try www.partstap.com