Very slow printing when it does run. has a flashing orange light alot too. have to unplug and replug to work

Not sure if you saw Tom's Guide
at Sharp lcd tv power button flashing

(1) 4tinyhearts said:
I unplugged the TV and held the buttons down and it continued to flash. I continued to hold down the two buttons and replugged it in again and it worked. TV back up and working.

(2) lastditcheffort said:
Unplugged it. After looking for a new tv online I decided to try getting it to work. So, plugged it back in and held down the power button, a red light came on, held down the power button again and an orange light came on, held down power button again and green light came on and tv powered on. This was simply a case of trial and success!

(3) Nateinportland said :
unplug, hold power button, plug in. If that doesn't work, unplug all the HDMI cables, unplug the power, hold power button, plug back in.

I think you have the upper light blinking and lower light solid. Is that right? The upper light blinking means that the connection to your ISP is not working. Try unplugging/replugging the Ethernet cable in the top port (probably yellow and labeled "WAN" or "DSL" or something). Check the other end of that cable. If you have another Ethernet cable, try swapping it out.

If none of that works, call your ISP to check the connection.

Some printers deny service even if there is only 1 cartrige empty.

As far as I know, the flashing lights are an indicator that the slow cooker is on, but awaiting instructions. You need to put in a time and then a temperature and then it will stop.

I personally find the power button very disconcerting and keep having to stop myself pressing it once I've programmed the slow cooker, and accidentally switching the thing off.

None of the above worked for me. There had been a paper jam, but I had cleared it. Orange "attention light" kept blinking. Unplugged the printer for about 15 seconds, replugged it in, and the error cleared.

Hi can gave you the truble codes

Light Orange - 2 beeps: Remove any paper jammed

Light Orange - 3 beeps: Remove any paper jammed

Light Orange - 4 beeps: Add Ink

Light Orange - 5 beeps: Re-install cartridge or replace it

Light Orange - 6 beeps: Re-install cartridge or replace it

Light Orange - 7 beeps: Re-install cartridge or replace it

Light Orange - 8 beeps: Waste is almost full

Flash 1 x Orange - 10 beeps (error code 6100): Try unplugging the printer for 30 seconds, if not requires service.

Flash 2 x Orange - 10 beeps (error code 6300): Try unplugging the printer for 30 seconds, if not requires service.

Flash 3 x Orange - 10 beeps (error code 6800): Try unplugging the printer for 30 seconds, if not requires service.

Flash 4 x Orange - 10 beeps (error code 5100): Make sure nothing is blocking the cartridge movement, if not requires service.

Flash 5 x Orange - 10 beeps (error code 5400): Try unplugging the printer for 30 seconds, if not requires service.

Flash 6 x Orange - 10 beeps (error code 5B00): Waste full (make a reset)

Flash 7 x Orange - 10 beeps (error code 5200): Replace the BJ Cartridge(Printhead)

Flash 8 x Orange - 10 beeps (error code 5200): Replace the BJ Cartridge(Printhead)

Flash 9 x Orange - 10 beeps (error code 5600): Replace the BJ Cartridge(Printhead) or reinstall it

Try unplugging it for an hour then plug it back in and press power. If its still flashing a blink-code then the tv is in protection mode and needs to be serviced. If the tv powers on normally after unplug/replug then purchase a digital surge-protector to prevent electrical spiking from hitting your tv again.

It flashes orange for a few seconds, and then back to green, and then back to orange every few seconds. I can't shut it off unless I unplug it. It also makes a horrible racket.

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00309184&lc=en&cc=us&dlc=en&product=374568&lang=en

You printer is giving you an error code with its flashing coloyr lights. I would consult canons website and write down the exact colours it is flashing as this is a specific error code. Most likely it is a paper jam error or reading error. Before you contact them i would try resetting the printer by powering down, unplugging all cables and cord, replugging and turning on and retry print jobs. If no luck go to plan B, webesite, and find error code. I am sorry i have no deatils for this printer to give you the error code myself.