#3 light stuck on (heat) washer will not run, Befor the washer froze I did hear a noise every 6 seconds for a whileand wan't sure where it was comming from, I think I know now.

If it is a front loading washing machineIt will probably either be in the pump outlet filter or be wedged between the inner drum and the outer drum ie. stuck on the heating element, depending on which type of washing machine you have.
1. Unplug the washer from the mains.
2.Turn water supplies off to the machine.
3.Open the door put your hand on the bottom of the drum inside the washer, lean a bit of your weight on the drum and turn the drum around. Can you hear a scraping noise?
If you can hear a noise, get a service engineer out as the ring is stuck between your inner metal drum and the outer plastic drum
4.If you cannot hear a noise. Lean the washer backwards and prop it up at the front so it is safe for you to gain access to the pump area,
5. Take the rubber hose clip off the pump with pliers, pull the hose off and feel inside the pump and filter basket, you might find your ring there.
6.Then replace everything as it was.

If the lights are not coming on, but you hear the pump, it could be stuck in the force drain mode. Let it run for about 2 minutes and see if it stops on it's own. If it does stop, try putting the unit into a regular cycle, if it lights up, you should be ok. If the pump does not stop, and lights are out, replace your control board. Make sure you follow recalibration instructions for machine to work properly.

take battery out and unplug laptop and hold power button for 30 seconds then plug in with out battery and see if it powers on

Hello.

It can be tempting to ignore washing machine noises, especially if the machine is still working. But washing machine noise is not only annoying, it can also be a sign of serious damage. When armed with a few tips, you can determine what problem may be causing your washing machine to rattle, and what you can do to stop it.

1 Check for drum bearing failure if your washing machine is noisy on the spin cycle. Drum bearing failure is common when the bearing seals start allowing water to enter. You can take the belt off and spin the drum by hand, and if the drum rumbles, replace the bearings.

2 Turn the drum by hand and listen for loud noises. If the drum itself is split or the 'spider' is corroded, broken or has come apart from the back of the drum it will create a loud noise on every turn of the drum. (When the bearings have gone bad, the noise is constant the entire time the drum is spinning.)

3 Look for obvious dents and creases in the drum or look for coins or small objects stuck inside the tub underneath the drum when a horrendous noise is made while clothes are in the tub.

4 Clear the water pump from obstructions like coins or small objects when a noise occurs while the washing machine is emptying water.

5 Remove the sump hose and look for bra wires if you hear a light scraping noise when the drum is turned by hand. You can also check to make sure a wire isn't poking out of one of the holes in the drum. In this case, you can pull the wire out easily with pliers.

6 Take the belt off and run the motor alone if you hear a high pitched squealing noise to check for motor bearing damage or wear. If you still hear the noise without the belt, it's the motor bearing.

Thanks.

Hi, . according to your washer problem i m writing solution ,please read and follow it:-

1. Most noises from a washing machine occur during the spin cycle. If you hear loud thumping during the spin, the load of clothes may have become unbalanced. Stop the washer and redistribute the clothes, then re-start it. Repeat these steps if necessary.
   
2. check out this following options one by one to locate the fault in your machine.
   
3. 1)Check for drum bearing failure if your washing machine is noisy on the spin cycle. Drum bearing failure is common when the bearing seals start allowing water to enter. You can take the belt off and spin the drum by hand, and if the drum rumbles, replace the bearings.2)Turn the drum by hand and listen for loud noises. If the drum itself is split or the 'spider' is corroded, broken or has come apart from the back of the drum it will create a loud noise on every turn of the drum. (When the bearings have gone bad, the noise is constant the entire time the drum is spinning.)3)Look for obvious dents and creases in the drum or look for coins or small objects stuck inside the tub underneath the drum when a horrendous noise is made while clothes are in the tub.4)Clear thewater pumpfrom obstructions like coins or small objects when a noise occurs while the washing machine is emptying water.5)Remove the sump hose and look for bra wires if you hear a light scraping noise when the drum is turned by hand. You can also check to make sure a wire isn't poking out of one of the holes in the drum. In this case, you can pull the wire out easily with pliers.6)Take the belt off and run the motor alone if you hear a high pitched squealing noise to check for motor bearing damage or wear. If you still hear the noise without the belt, it's the motor bearing.
   
4. you can get the required partys from
   
5. www.repairclinic.com
6. I hope this will help.

please don't forget to vote me. goodluck.......

Instructions Things You'll Need:

• GE/ lg washer

Primary Method---Newer models
1. Step 1 Unplug the washer.
   
2. Step 2 Twist the control dial around the cycle settings.
   
3. Step 3 Place the dial on any setting other than the final spin.
   
4. Step 4 Ensure that the water line is securely attached to the washer.
   
5. Step 5 Plug the washer back into the wall (making sure it has gone at least 30 seconds without power).
   
Alternate Method---Older Machines
6. Step 1 Turn the dial around the cycle settings, but do not lift it to start the cycle.
   
7. Step 2 Unplug the washer.
   
8. Step 3 Plug the washer into the wall after 30 seconds without power.
   
9. Step 4 Lift the washer lid five times, making sure it reaches a height of at least 6 inches or more. There should be no more than a 15-second interval between lifts.
   
10. Step 5 Listen for a clicking noise. If a click is not heard, repeat steps 1 to 5 until you hear it.
    
11. Step 6 Place a small load of laundry into the washer and start the cycle.
    
12. Step 7 Watch the load throughout the wash to ensure the washer is working properly.
    

The heated seats have relays that run them. Not quite sure where they are located but. That noise is the relay clicking on and off. They are actually pretty loud. Look for faulty connections to and from the relay and check battery power to both sides of the relay.

Yes Get a space heater and run it by the frozen pipe. Turn off all electricity to avoid shock and it should break free by the morning. Run it at a drip from now on during really cold night just like the sink but set washer on DRAIN this will help. Good LUCK

If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).

To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

If the issue returns, you could have a problem with the heating circuit (ie. element, thermostat or wiring). It rarely happens but it could also be the door switch not engaging properly when the door is closed (slightly bend the door latch down making sure it doesn't hit the door when you close it).

Do a "key dance" between normal and heated dry , going bak and forth six times. this will rester the heater fault. That is the clean light flashing code. Now you have to find the cause. Most likely is that there were suds in the last cycle or the door doesn't close smoothly. If the door sttrikes the cabinet in any way it will cause that problem.