Hp laserjet 1200 printer problem

HP tech support might help you in this matter you can reach them directly on this number (877-690-9305) or just follow the link Support For Hp Printer

HP LaserJet 1022 cold reset procedure To cold reset the printer, perform the following steps:

1. Power off the printer.
2. Power on the printer while depressing both the Go and Cancel buttons. Keep the buttons depressed. The lights will begin to flash in sequence.
3. Release the buttons when all three lights begin to flash in unison.

The printer is now reset and ready for use. Back to top HP LaserJet 1018 and 1020 cold reset procedure To cold reset the printer, perform the following:

1. Power off the printer.
2. Power on the printer.

The printer is now reset and ready for use. NOTE: The HP LaserJet 1020 printer is completely initialized at power on. Essential printer information for the printer is stored in the driver software and downloaded to the printer with the print job.

If you want the printer driver for your HP printer then -
You can download the HP printer drivers from their supportWEB site. Please click on this link and select your model printer to download:- http://welcome.hp.com/country/us/en/support.html

May b your printer needs some servicing.
The black line may be caused by a faulty or used fusing film or fuser roller.

check the usb cable or its port ,or try print a test page from the printer by pressing front pannel button 5 second and release. if printng a test pasge its ok the printer

Follow this link and see the availability of drivers for your printer. Just type your printer model and search (Eg laserjet 1200 )

or copy and paste this link to your another window of the browser
http://www.hp.com/#Support

Turn the printer on.
2 As the printer performs its power-on sequence, press and hold the PAUSE/RESUME (HP Color
LaserJet 4600 models) or MENU (HP Color LaserJet 4610n and 4650 models) button until all
three lights on the control panel are lit.
3 Press . The message INITIALIZE DISK appears on the control-panel display.
4 Press The printer initializes the hard disk and continues its power-on sequence.

Hello,

It seems that none of the printer's sensor is faulty, in fact, the printer has a faulty firmware on the formatter.

Your printer may need replacement of the formatter board, however, please try the following before swapping the formatter.

HP LaserJet P2015 Printer Series - Paper Jam Light Solid ISSUE: The HP LaserJet P2015 may come up with Paper Jam Light solid and would show the same light pattern even if the printer is power cycled.
SOLUTION: The Light pattern is as shown in the diagram below.

Perform the following tasks in the order listed.
1. Reset the printer using the Super NVRAM initialization. The procedure is
a. Turn off the printer
b. Press and hold the GO button
c. Turn on the printer and continue to hold the Go button for at least 50 seconds. During this process the Attention, Ready and Go light turns on. Then the Attention and Ready light turns off, leaving just the Go light illuminated.
d. Release the Go button. The Go, Attention and Ready lights turn on.
e. Press and hold the Go button. All lights turn off. During the next three seconds, the Go, Ready and Attention lights turn on in that order, one per second.
f. Release the Go button to perform the initialization. The control panel lights begin cycling from front to back. After the Super NVRAM initialization process is complete, the printer returns to the ready state.
2.Unplug the power cord when the printer is on and leave it unplugged for 10 Seconds.
3. Turn the printer back on.
If the above steps resolve the issue, then print a configuration page and check the firmware version and the formatter board no.,
If the firmware version is below: 20080312, then your printer needs to upgrade the firmware, however the firmware can be upgraded only onl those models whole formatter board's third number from left is 0, 1 or 2, eg: JK0xxxx

If the 3rd number from left of the formatter board no is anything other than 0, 1, 2, then firmware cannot be flashed.

Please let me know the next update.

- Nikhil

Hello,

Please perform the following.

Super NVRAM initialization Turn off the printer.

1. Press and hold the Go button.
   
2. Turn on the printer and continue to hold the Go button for at least 50 seconds. During this process, the Attention , Ready , Go lights turn on. Then the Attention and Ready lights turn off, leaving only the Go light illuminated.
   
3. Release the Go button. The Go , Ready and Attention lights turn on.
   
4. Press and hold the Go button. All lights turn off. During the next three seconds, the Go , Ready and Attention lights turn on in that order, one per second.
   
5. Release the Go button to perform the initialization. The control panel lights begin cycling from front to back. After the Super NVRAM initialization process is complete, the printer returns to the ready state.
   

In your printer driver Cd there are three type of hp laserjet 1200 installations you can find out. pcl5/pcl-6 /and ps versions. Try to print your bill form through these three driver sioftwares.And moreover i want to know that what software format you are using in your bill printing ?.