Mdg9700a flame wont stay burning. It wont get warm

Question 1

0helpful

1answer

Totai heater wont stay on after lit

Without a pilot flame sensor signal the pilot light will not stay on and the heater won't work. Try Replacing the pilot flame sensor, the pilot flame burns on to it and it connects to the valve. It looks like a wire.

Nov 26, 2017 • Rinnai RHFE-1004FA 38,400 BTU Energy Saver...

0helpful

1answer

Maytag Dryer runs for 8-10 seconds then shuts off accompanied by burning smell

When you say it runs for 8 - 10 seconds, do you mean it spins for that long or the flame is lit for that long?

Dec 01, 2012 • Maytag Neptune MDG9700A Gas Dryer

0helpful

1answer

Goodman furnace gmh95090cxac wont stay lit keeps clicking will lite then clicks back off what would be the problem

Hello, if the burners light but do not stay on for more than 10 seconds, I would clean the flame sensor. The flame sensor is a metal rod that is on the opposite side of the Igniter, sometimes it gets coated by oxidation and does not sense the burner flame and shuts the Furnace down. To clean to kill power to tje furnace, remove flame sensor and clean with a steel wool, then reinstall and start Furnce back up. If this does not work then most likely the Igniter is too weak to ignite the gas and will have ro be replaced.

Oct 29, 2012 • Heating & Cooling

0helpful

1answer

Oven wont stay lit

If you are talking about the little flame that is supposed to be burning at all times then you need to go to a hardware store and purchase a thermocouple. It is a small copper tube that sense's the flame. When working it will constantly burn a pilot flame so that when you turn on the oven it will ignite the gas in the burner. Once the burner is lit it will stay lit until the oven reaches the desired temperature. Replace the THERMOCOUPLE.

Sep 09, 2011 • Belling Solitaire G755 Gas Kitchen Range

0helpful

1answer

Pilot light wont stay lit, even when on high

Pilot lights are supposed to stay on when the flames are burning. If they didn't the flames would go out, because the pilot flame against the Thermocouple keeps the pilot burning. It's a safety feature.

Mar 08, 2011 • Heating & Cooling

2helpful

1answer

My dryer takes hours to dry one load of clothes. Cleaned all lint from it. It's warm, not hot. Flame is on.

you need to either dismantle the venting pipe ductwork inside the dryer and get inside the duct and loosen all dried on lint which is holding moisture in,otherwise the cycling switch for the flame is cutting out tooooo sooooon and your not drying the load properly per selected load setting

Mar 14, 2010 • Maytag Neptune MDG9700A Gas Dryer

2helpful

1answer

I have a blue flame GLO WARM 20btu wall model # WMP20A

Look for and clean the flame sensor.

Dec 06, 2009 • Desa International Blower Glow Warm Wall...

0helpful

1answer

Vent less gas heater wont stay burning. starts nice blue flame and than goes out no polite lite no flame.

If your heater does not stay burning then you should check each of the internal components over to ensure that they are working properly. Look at your heater's manual to do this. Failing this, the best thing to do is to buy a new one as the cost of repairing one can cost loads of money. Good luck :)

http://www.ventless-gas-heaters.com

Nov 29, 2009 • Desa International Comfort Glow Infrared...

0helpful

1answer

Have a Maytag gas dryer, model#:LDG7314AAE, flame wont stay lit.

Clean/repair your dryer vent. The flame when it exits the funnel should not touch or just barely touch the funnel end. This indicates good airflow. A good test for the clogged/damaged vent is to disconnect the vent hose from the dryer and run it as is. If the flame stays - clean vent. If not - clean air path inside the dryer

Nov 17, 2009 • Refrigerators

0helpful

2answers

Blue flame heater pilot wont stay lit

There is a therma-couple that the flame burns against. When it is working correctly it allows gas to travel to the flame. When it goes out you get no gas, as a safety feature. Replace the therma couple and it should work again.

Oct 06, 2008 • Dyna-Glo D-E36 Infra-Red Wall Mounted...

Question 2

Anonymous

Contributor 1 Answer
Posted on Mar 25, 2011

Anonymous

Contributor

Joined: Mar 25, 2011

Answers

1

Questions

0

Helped

397

Points

2

We have a front loader neptune MDG9700AWW .gas dryer that won't heat up . I did all the proper cleaning to it but still not getting any heat to it

Answer 2

jimorris77

Master 411 Answers
Posted on Nov 26, 2009

jimorris77

Master

Joined: Nov 14, 2009

Answers

411

Questions

0

Helped

96549

Points

1202

I am not a repair professional. I am just a 78 year old man who has been making his own repairs for about 50 years. Therefore the dryer ID doesn't mean
anything to me. Over the years, I haven't had much trouble with my dryers. However I can suggest you go to www.applianceaid.com where they have very good trouble shooting and repair information on dryers and other appliances. I think you'll find what you need there. If you have an error code you can probably find the meaning of it there. Good luck with it. If I have helped you, please rate my advice on fixya.

Related Topics:

Trustworthy Expert Solutions

Mdg9700a flame wont stay burning. It wont get warm

2 Answers

Anonymous

jimorris77

Add Your Answer

Attachments: Added items

Related Questions:

Totai heater wont stay on after lit

Maytag Dryer runs for 8-10 seconds then shuts off accompanied by burning smell

Goodman furnace gmh95090cxac wont stay lit keeps clicking will lite then clicks back off what would be the problem

Oven wont stay lit

Pilot light wont stay lit, even when on high

My dryer takes hours to dry one load of clothes. Cleaned all lint from it. It's warm, not hot. Flame is on.

I have a blue flame GLO WARM 20btu wall model # WMP20A

Vent less gas heater wont stay burning. starts nice blue flame and than goes out no polite lite no flame.

Have a Maytag gas dryer, model#:LDG7314AAE, flame wont stay lit.

Blue flame heater pilot wont stay lit

Not finding what you are looking for?

Neptune MDG9700A Gas Dryer

Totai heater wont stay on after lit

Ask a Question

Top Maytag Dryers Experts

Mike Cairns

ZJ Limited

Brad Brown

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

Trustworthy Expert Solutions

Mdg9700a flame wont stay burning. It wont get warm

2 Answers

Anonymous

jimorris77

Add Your Answer

Attachments: Added items

Related Questions:

Totai heater wont stay on after lit

Maytag Dryer runs for 8-10 seconds then shuts off accompanied by burning smell

Goodman furnace gmh95090cxac wont stay lit keeps clicking will lite then clicks back off what would be the problem

Oven wont stay lit

Pilot light wont stay lit, even when on high

My dryer takes hours to dry one load of clothes. Cleaned all lint from it. It's warm, not hot. Flame is on.

I have a blue flame GLO WARM 20btu wall model # WMP20A

Vent less gas heater wont stay burning. starts nice blue flame and than goes out no polite lite no flame.

Have a Maytag gas dryer, model#:LDG7314AAE, flame wont stay lit.

Blue flame heater pilot wont stay lit

Not finding what you are looking for?

Neptune MDG9700A Gas Dryer

Totai heater wont stay on after lit

Related Topics

Ask a Question

Popular Questions

MAYTAG PERFORMA ELECTRIC DRYER WONT START

My Maytag dryer won't start when I hit the start button

Sail switch open fault

How to remove the front panel of a maytag bravos

Maytag dryer epic z how to reset f1 code it is flashing

Top Maytag Dryers Experts

Mike Cairns

ZJ Limited

Brad Brown

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Manuals & User Guides