Question about Washing Machines

1 Answer

Kenmore washer model series 23711 pn 10182371800

About 2 months age I started have wet closes so I just spun them again. Today I looked in and they still had water in the botton of the tub. I tried spinning again but no luck. I seen that the center agitator moved but the tub didn't move. I looked at the belt it looked ok and kinda of tight. I thought that it might be a filter and I didn't see one on this model in the diagram for the model. Can you tell me what the problem might be and if I can fix it myself. I don't have any experience with repairing washers. Its an old model maybe its time for a new one or a professional.


I have a model # 11024832200. I purchased it in 2003. It is a Kenmore 80 series. For a while I have had to respin my clothes. Just recently I have had to give the washer a little boost and help start spinning the tub. It would start spinning on its own with a little help and finish the job of spinning the clothes. The poor thing finally quit spinning all together. The agitator works fine. It still washes the clothes, but I have to wring them out by hand. Please help.

Posted by on

  • nurseannie Jan 14, 2008

    The washer is a Kenmore 80 series. I bought it new in 2003. The model # 110 24832200.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers

Nurse annie give me your model number and approx age .and will be happy to advise mike give me the age of your washer as you might not have the same problem

Posted on Jan 14, 2008

  • robert samples Jan 14, 2008

    ok sweetie let me look at a few things and ill get back to you we can fix anything ok

  • robert samples Jan 14, 2008

    hon that model number you gave me dont have a belt its direct drive 2003 isnt old for a washer where did you get the model number get it off the washer serial plate ok



1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Kenmore 417.43142200 final spin is slow

obviously the timers contacts are bad so replace the timer.

May 16, 2017 | Kenmore 43142 Front Load Washer

1 Answer

Washer won't drain or spin

you need to check the water pump... it may be clogged with detergent or something to that effect.. or just replace the pump itself..

Oct 11, 2009 | Washing Machines

1 Answer

My Kenmore Series 80 washer model 23832100 spins slowly

It probably is your clutch. You will need to remove transmission to repair this.

May 12, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore 70 series washer will not spin, clothes are too wet

Not a belt, this is only a sound deadening devise on the brake housing. Not really needed. Replace the coupler

Jan 03, 2009 | Kenmore 24032\24036 Top Load Washer

2 Answers

Kenmore Front load washer didn't complete the cycle.model #44082

Do you still have your owner's manual that came with the Kenmore washer? Look under troubleshooting your Kenmore washer.

Jul 06, 2017 | Kenmore 44102 Front Load Washer

1 Answer

Kenmore 80 Series Heavy Duty Super Capacity Plus

that is a whirpool source washer suspect wire underneath console may be where connector from wall plug connects underneath ckd all wires around timer possible power loss has been problem from the first but try to some action going again first good luck

May 21, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore washer model series 23711 pn 10182371800

Hi, check the drain pump clean the infeller and also check hose struck of linen build up .

Jan 13, 2008 | Kenmore 24032\24036 Top Load Washer

8 Answers

Kenmore Washing Machine 70 series

You most likely have a broken coupler between the motor and gearcase.
You can buy the part for about $10 or have someone come out and replace it for about $150-200.
If you will post the complete model number from the the washer so I can see which style cabinet you have, I will try to walk you through the repair. It isn't very complicated if you are handy with home repairs.
With the age of the machine it probably just needs a coupler, but it could also have a problem in the transmission or basket drive that has caused the failure.

Nov 13, 2007 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides