Unit not sending wireless signal to secondary pc

You need a wireless card. It could internal or external as a USB device.

GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

heres a list of fault codes hope it helps

John

Yes. You can use two routers. Your first router is your most main router. Then you can put your second router where you want to use it. If for example, your house has three floors, your main router should be on the first floor only. Take your second router to the second floor only because that signal will reach the third floor.
How do you configure?
It is better that you just buy internet cable or LAN cable here. You can see the photo at this link


Connect it to the main router usually on the first LAN port and then connect the other end to your second router so that you can have internet. Visit Here For Router Products Visit

Double check the batteries and the direction in which they are installed. If there is one backwards in the sending unit that is outside, it will not send a signal. Also, there is typically one battery in the indoor unit that is responsible for receiving the signal from the outdoor unit. If all of the batteries are in correctly except that battery, you will see the display, but will not get the data transmitted from the outside sending unit.

That is the Suzuki equivalent to a "Check engine light"

Turn your key on and verify the FI light is on and that your red kill switch is set to 'Run'

Remove your seat and behind the battery area you should find a white 6 pin connector (likely with a black rubber boot on it) Using a paperclip connect the white/red striped wire to the black/white striped wire.

Your display should Now read whatever codes are active.
If it reads C00- then there are no active codes. Note that when you turn the key off, the memory is erased so if you have an intermittent fault you should not turn the key off until you pull the codes.

Codes are as follows:

C11 - CAMSHAFT POSITION SENSOR
C12 - CRANKSHAFT POSITION SENSOR
C13 - INTAKE AIR PRESSURE SENSOR
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C36 - SECONDARY INJECTOR SIGNAL #1
C37 - SECONDARY INJECTOR SIGNAL #2
C38 - SECONDARY INJECTOR SIGNAL #3
C39 - SECONDARY INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR
C49 - PAIR CONTROL SOLENOID VALVE
C60 COOLING FAN CONTROL SYSTEM

goto start - run - .cmd - enter..type ipconfig..you`ll get ip address,subnet mask,default gateway.copy it.goto start- control panel - network connections now right click wireless network connection and click on properties and double click on internet protocol(TCP/IP) or if you are using vista goto network and sharing center - view status - properties - double click on IPv4.type in the IP address,subnet mask,default gateway.in DNS server address type the default gateway in primary DNS and in secondary 4.2.2.2. your connection won`t drop after this.
this will fix your problem...

i believe the simplest way to do this is to buy a external USB wireless adaptor for your computer. thats saying that your dsl modem has a wireless signal being broadcasted already . if you dont have wireless built into your DSL or Cable modem, you will also need a wireless capable router to send it to your computer...
keep in mind that the wireless external network adapter could easily be used with ANY computer to connect wirelessly, so it's not limmitted to just your current hardware.

have you tried un-installing and re-installing. this usually helps.

have you treid reconfiguring the settings ?

Did U use the setup cd for the new wireless?

set the second router through the web menus to a different ip address, cant have 2 devices on the same (default) 192.168.0.1 address, try 192.168.0.2 (example only) to stop data collisions
connect by cable secondary router lan port 1 to the primary router lan port 4 (any lan port to any lan port),
drag secondary router upstairs on its cable and install it wherever you want
set two routers on different channels.
set all wep settings on both routers the same.
set all pcs to 'auto channel' select
wireless adaptors in pcs will then select strongest signal at any point and transmit thru that router