Dsl user name and password - Linksys WAG200G Router

http://dlink-manuals.org/dlink-dsl-1504g-user-manual/

plug router and a computer together via ethernet cable and type in 192.168.0.1 and havre computer setup to use dhcp in internet settings. Try user name admin password admin
if it does not accept the default password and user name you will have to read up in the manual how to reset dsl 1504 to factory settings.

You'll have to contact your Internet Service Provider(ISP) and ask for the DSL username & password.

DSL uses a ppoe account. Your DSL provider should have given you a router/dsl modem to connect to the internet, and then you can use another router to feed the house a wireless connection. The ppoe user name and password should be set up on one of these devices. If you don't know what your user name and password is, (I forgot mine a long time ago), you can contact your provider and have your password reset. Once this is done, you will either have to connect via wire to the device that should have your user name and password, and set it. Default IP address to get into this router is 192.168.1.1, type that into your address bar on your browser.

default user name and password are both admin, all lower case for both.

Once you get into the device then you can go into the setting and look for connection settings.

Here is the PDF for this router. Start looking at page 5 to learn how to set up a ppoe user and password.
http://www.quickline.com/Shop/Documents/Benutzerhandbuch_WRT160N.pdf

i am not sure what king of network you may have.. if you have DSL make sure that you have a DSL filter on the phone jacks, next make sure that the router or DSL is seeing green lights called DSL / Power / Ethernet is more likely standing light, next you will see green light flashing / that called Internet.

and rule number one make sure that your user name and password is right. make sure that there no space or some thing that should not be in the password or user name.. if you need more help i am glade to help you more out

If you don't remember your password the best thing to do is to reset the router.
1. Turn off your dsl or cable modem. Keep the router plugged in to the wall.
2. Find the reset button on the back of your router.
3. Use a pen to press the reset button.
4. Hold the reset button down for about 30 seconds.
5. The lights will flash on the router.
6. Turn your dsl or cable modem on again.
7. Reconfigure your router. It will be set to the default user name and password. User name should be blank and password is "admin" without the quotes.

unplug all the wires and replug them again and check the browsing. Or if it can't be done then reset the modem by pressing the reset button that would be there on the back of the modem and reconfigure the modem. By typing 192.168.1.1. With the user name and password that should be user name :admin and Password : password or user name : admin and Password: admin. Put your details and save and reboot the modem and then check.

You need to visit your router's web interface at http://192.168.1.1 or http://192.168.0.1 (whichever works with your router)

If you are prompted with the password, then use these defaults:
user name = admin
password = <leave blank>
OR
user name = admin
password = admin
OR
user name = <blank>
password = admin

If you have your user name and password for the router, you can direct connect with and ethernet cord, then go to Start -> Run and type "cmd" without the quotes of course. When the faux DOS comes up type ipconfig and press enter. Find your ip address (I think the default for these routers is 192.168.1.1) open internet explorer or the like and type 192.168.1.1 into the address bat and press enter. It should prompt you for your user name and password. If you have not set one the user name should be admin and the password will be either password or admin. you can go into your router and see what your passphrase is or change it altogether.

You need to call your ISP. They can reset passwords and user names. I work with an ISP and it happens all the time. System erase things and you will need them to help. Hope your the acct user cause we guard info heavily.

It didn't work for me.
Should the username be the email address from At&t that controls the DSL line, or should it be the username to get into the Netopia modem?