Question about Belling Ovens

1 Answer

Belling countrychef - Main oven gas doesnt stay on after ignition. We tried holding the knob in for 3-4mins but gas cuts out as soon as you let the knob go. there is no debris on the burner etc

Posted by jon_merrick on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

The flame failure device has failed ,you will need a new thermocouple

Posted on Nov 18, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My belling wall oven model number 444440560 keeps going out after only a few seconds ignition how can I fix this thNks


which is going out top or bottom? may want to check the oven safety valve though it does not normally go out compared to other components. may have a bad igniter ( does it glow or lite up at all) it may still glow but not put out enough current to ignite flame? check with multimeter as well. if oven top is going out also check the igniter model or infinite switch

Mar 10, 2015 | Belling Ovens

1 Answer

Gas oven does not stay ignited


Does your oven need an electric connection? Check if the plug is in the socket properly, if it is change the fuse and see if it works. If it does work check the. lead for a possible bad connection in the fusetop

Jan 21, 2013 | Ovens

1 Answer

My ovens wont stay alight i have a twin range gas oven and it just wont stay lit but if i hold the knob in it stays lit


I offer free advice bcuz God is so good!
GAS OVENS
The spark igniter tip is dirty (can clean it with either a little wire brush or a piece of fine sandpaper).
2) The Pilot flame is too low, and the tip of the igniter is not in the flame good enough. (the flame acts as a circuit when it touches the tip & completes the circuit).
3) The spark module is no good and needs to be replaced.(But 1 & 2 are your best bet).
spark module does not sense the flame when it's on. The spark igniter is also the flame sensor which provides feedback to the spark module.

Make sure the igniter is properly aligned with the burner lighting holes and it is clean. All lighting holes must be clean too. You can enlarge them using a drill bit one size bigger.

If it would not fix the problem, replace the bake burner and the igniter.
There is a small chance for the spark module itself to be bad as well.

The oven safety valve
(also called the gas valve) is the part that ensures that gas is not released until the igniter has reached the correct temperature needed to ignite the gas. While this part can fail, it is uncommon. If the hot surface igniter does not glow you should first verify that you have voltage to the circuit. This is a live voltage check and should be performed by a qualified person. If voltage is lost at the valve terminals then you should verify the continuity of the bi-metal in the valve using a multi-meter.


ELECTRIC OVENS:

CHECK THE OVEN RELAY CONTROL BOARD Aclicking sound could be something wrong with a relay. Check for any loose connections around the main control board on your oven. The click you hear is a relay losing power and switching back on. If the clock resets then something is causing power interruptions to the board.

: I offer free advice bcuz God is so good!

Jul 31, 2011 | Belling Ovens

1 Answer

I have a Frigidaire model FCG30B6Q0JWI-5A gas stove (Made in Costa Rica) and can't get the oven to stay lit. There is no electronic ignition, no pilot, it's just a regular run-of-the-mill light a...


Hello,

While your holding in the knob after lighting the pilot,their is a thermocoupler that is heating up and will hold automatically what your pushing in, that thermocoupler is defective

Jul 28, 2011 | Ovens

1 Answer

Flame will not stay lit in oven of countrychef 100g


Yes very simple. There is a bulb the flame is heating with a small tube that runs to the gas valve this is the saftey sensor that is bad called a thermo-couple , they are common to go out and should be easy to find online. Let me know if you have any other questions.
Phil

Apr 10, 2009 | Ovens

Not finding what you are looking for?
Ovens Logo

Related Topics:

852 people viewed this question

Ask a Question

Usually answered in minutes!

Top Belling Ovens Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Harrie

Level 3 Expert

6746 Answers

Are you a Belling Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...