401 unauthorised cannot view router setup - Belkin (F5D7230-4) Router (587009)

No, but you can just reset the whole router and start from scratch. Hold the reset button on the rear of the router for 60 seconds and your will restore the unit to defaults, at which point you just need to reconfigure all of your configuration settings and password, as well as your wireless access code. Let me know if you require any additional assistance.

" 401 unauthorized" authorization required " .This message means the user name and password for the router is not correct. the default password of the Linksys router is admin with no user name ( leave it blank )
If the default password is not working then the router password must be changed.
If you don't know the password of the router then you will need to reset and reconfigure the router.
Once you reset the router , it will come back to the factory default settings.
Click here for more info about router and network

A WPA Key is the network key you use to connect up to the wireless on a router. It prevents unauthorised use of your internet connection. If you need to get to this it is often printed on the bottom/side of the router somewhere as network key or security key. If it's not there then you'll have to go into the router setup and into the wireless section and find what the key is in there.

The default password of the linksys router is admin just leave the username blank, if admin did not work reset the router so it will be back to its default settings with default password admin and leave the username blank ..

Hope that helps........

If that won't work it only means that it's already been changed you just reset the router by pressing the reset button for 30 seconds.

i take it by your comment "unauthorised people been accessing it" that you wish to use the router wirelessly? do you currently have any type of encryption set up on the wireless signal at the moment eg WPA(2)-PSK, WEP, etc?

Getting the 401 Authorization Required error page means that you tried to access a Setup page and entered an invalid password three (3) times. To reset the password, the device must be reset to factory default settings. Resetting the device: 1. Hold in the Reset button (usually located on the front or back panel) for 30 seconds. 2. Unplug the power cord to the device and wait for 1 minute. 3. Plug the power cord back into the device. 4. This will restore the device's default settings, which includes a default password of admin. 5. You can now try to access the Setup page again. Accessing the Setup Page: Open a Web Browser (either Internet Explorer or Netscape). Type the IP Address of the device into the Address Bar and press [Enter]. 1. The User Name and Password Prompt will appear. 2. Leave the User Name Field blank. 3. Type in the Router?s Password, admin, (the default Password). 4. Click OK or press the [Enter] key. If the device was reset to factory settings, the password of admin should be valid and the Setup page should load. If not, repeat steps to reset the device.

Getting the 401 Authorization Required error page means that you tried to access a Setup page and entered an invalid password three (3) times. To reset the password, the device must be reset to factory default settings. Resetting the device: 1. Hold in the Reset button (usually located on the front or back panel) for 30 seconds. 2. Unplug the power cord to the device and wait for 1 minute. 3. Plug the power cord back into the device. 4. This will restore the device's default settings, which includes a default password of admin. 5. You can now try to access the Setup page again. Accessing the Setup Page: Open a Web Browser (either Internet Explorer or Netscape). Type the IP Address of the device into the Address Bar and press [Enter]. 1. The User Name and Password Prompt will appear. 2. Leave the User Name Field blank. 3. Type in the Router?s Password, admin, (the default Password). 4. Click OK or press the [Enter] key. If the device was reset to factory settings, the password of admin should be valid and the Setup page should load. If not, repeat steps to reset the device

Getting the 401 Authorization Required error page means that you tried to access a Setup page and entered an invalid password three (3) times. To reset the password, the device must be reset to factory default settings. Resetting the device: 1. Hold in the Reset button (usually located on the front or back panel) for 30 seconds. 2. Unplug the power cord to the device and wait for 1 minute. 3. Plug the power cord back into the device. 4. This will restore the device's default settings, which includes a default password of admin. 5. You can now try to access the Setup page again. Accessing the Setup Page: Open a Web Browser (either Internet Explorer or Netscape). Type the IP Address of the device into the Address Bar and press [Enter]. 1. The User Name and Password Prompt will appear. 2. Leave the User Name Field blank. 3. Type in the Router?s Password, admin, (the default Password). 4. Click OK or press the [Enter] key. If the device was reset to factory settings, the password of admin should be valid and the Setup page should load. If not, repeat steps to reset the device.