Question about BenQ FP737S-D 17" LCD Monitor

2 Answers

Power light on no screen shown - BenQ FP737S-D 17" LCD Monitor

Posted by snowfire on

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 28 Answers

Unplug from pc, turn on monitor. if there is a 'no signal' or any image displayed on the screen then the problem is not the monitor..

Posted on Nov 15, 2009

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Turn power on, see benq logo, then goes dark. it is a fp 737s

Posted on Apr 02, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I turn on dell vostro 1520 and screen is blank. Screen shows to activity at all. On status bar between keyboard and screen POWER, CAP LOCK AND + indicator lights are lit solid. The NUM LOCK indicator is...

Attach to external monitor, if it works, there is a fuse that is blown near the video output cable. Not big enough for a novice to fix.
If not shown on external, it is a dead lcd, or bad solder ball issue. Quite common on those models.

Fuse details may be shown on my webblog. "Getting In Too Deep" Google it. Then search for Dell - it should come up in the list.
0helpful
1answer

Could you show me the correct way how to power up the hard drive box a green circular light is by the power cord is on when plug up but the fan is not running could you show me what is wrong the computer...

Could you take a picture of the entire back of the PC? You only show the power supply connected with power, what about the graphics card output? and power to your monitor etc.?
0helpful
1answer

My screen is dark but the sound is ok

SOUNDS LIKE EITHER THE INVENTER BOARD IS PLAYING UP OR THE POWER SUPPLYBOARD,LOOK FOR FAULTY CAPACITORS.ITS THE BACKLIGHT THAT LETS YOU SEE WHAT IS BEING SHOWN ON THE LCD SCREEN BY LIGHTING IT UP,IF YOU LOOKED CAREFULLY OR SHOWN A TORCH ON IT YOU WOULD SEE THE SCREEN.SOMETIMES IF YOU MANAGE TO TURN THE BACKLIGHT DOWN A BIT BY TURNING DOWN THE BRIGHTNESS ON TV,THE BACKLIGHT WILL COME ON AGAIN,IT IS CUTTING OUT DUE TO LACK OF POWER OR FAULTY CAPACITORS ON THE PSB.DO SOME GOOGLE SEARCHING,GOOD LUCK
0helpful
1answer

Message "job pending " is shown in the screen of

take the power out.
hold the stop botton.
put power back
6helpful
1answer

I have a cybershot DSC W55. When the power button is switched on the lens extends and the "access" message shown on screen. Also amber light is flashing above screen. After a few seconds I get a...

I have a cybershot DSC W55. When the power button is switched on the lens extends and the "access" message shown on screen. Also amber light is flashing above screen. After a few seconds I get a message to power on and off again. I\'ve tried switching on and off a few times, removing battery pack and memory card, but nothing seems to be solving the problem.
0helpful
1answer

Replaced broken motor coupler and motor still saying problem has been detected with drive system

With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control.

Solution:

  1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.


  2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.


  3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed.
8helpful
1answer

Wont run

  1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.


  2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.


  3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

0helpful
1answer

GE PROFILE WASHER DOESN'T CYCLE TO WASH FROM FILL

  1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.


  2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.


  3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Not finding what you are looking for?
BenQ FP737S-D 17" LCD Monitor Logo

Related Topics:

612 views

Ask a Question

Usually answered in minutes!

Top BenQ Computers & Internet Experts

Ekse

Level 3 Expert

13435 Answers

Joaquim Martins

Level 3 Expert

1128 Answers

Manoj

Level 2 Expert

127 Answers

Are you a BenQ Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...