Question about Televison & Video

2 Answers

Hitachi 60sx2k vertical hold

I got the a hitachi 60sx2k for free. when I got it home, I found out that the vertical hold was out. I have been trying to find a repair person in the area, but the closest one to me is about an hour away (I live in the country). I was wondering if there is a "common" fix for this problem? if so can someone direct me. I have downloaded the service manual on line and have a fairly good handle on electronics so I am not afraid to break out the iron.

Posted by on

  • kaneq Jan 07, 2008

    The picture is there and will stabalize (kinda) once in a while (very wavey) , but most of the time it scrolls

  • Gary Beechler Dec 27, 2008

    only rolls when the picture is dark - when it is bright it doesn't roll



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

PIP bord capacitor licking

Posted on Oct 16, 2008


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,153 Answers

You say vertical hold, are you saying you can see the picture but it rolls or is the picture not there? For more info

Posted on Jan 07, 2008


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the vertical hold button

This set has no vertical hold control---is picture rolling left right or up down?

Mar 10, 2012 | Hitachi 57F500 57" Rear Projection...

1 Answer

Vertical hold on a hitachi 53 inch projection tv, does not work on a/v inputs picture is stops rolling on hd inputs. Please help..

The set needs proper attention to its vertical output section, and synchronising seperatror sections. You must have through knoledge in electronics and repairing circuit boards. If you have, replace all the electrolytic capacitors at its vertical output section.

Feb 20, 2012 | Hitachi Televison & Video

1 Answer

I have a 60sx2k alignment won't hold

There can be a number of causes for this behavior. At this point I would suspect the convergence ICs. If you can solder, I would start by resoldering the pins of the convergence ICs. If that does not resolve the problem, then I would next change the ICs. I really believe that the solder connections are the problem as the unit would not converge were the ICs defective.

Please keep us posted on your progress.


Dec 03, 2009 | Hitachi Televison & Video

1 Answer

Cannot Locate The User's Manual for Hitachi HB-B102

Hi Kay. Goto www.manualsonline join for free. Your manual can be found there!

HB-B101Manual.pdf. If this solution has assisted you, please rate it. ricardok45.

Mar 14, 2009 | Zojirushi BBCC-X20 Home Bakery Supreme...

3 Answers

Vertical lines on screen

1. Frist on the BURN MODE.
2. Check whether same
Vertical lines on screen ?? 3. If yes ..?
4. Then change the LOGIC BOARD or PDP

Jan 11, 2009 | Hitachi 42HDS69 42 in. Plasma Television

1 Answer

Remote code

Hello steeler,
I am David thank you for choosing for your answer.

I went to the comcast site and found the numers you have there is another way to try also here it is

Searching for a code If your home entertainment device does not respond to the remote control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.
Example: You've tried all the codes for your TV, but you still cannot get the remote control to operate your TV.
  1. Turn on your TV.
  2. On the remote control, press TV once.
  3. Then press and hold SETUP until the TV key blinks twice, then release the SETUP key.
  4. Using the number pad, enter 9-9-1. The TV key will blink twice.
  5. Aim the remote control at the TV and slowly alternate between pressing Power and TV. Stop when the TV turns off after pressing the POWER key. This means that a working code has been found.
  6. Press the SETUP key once to lock in the code. The TV key will blink twice.
I hope this helps you with your tv Thank you again for using
feel free to rate me on my answer thank you again.

Nov 06, 2008 | Hitachi HL01453 Remote Control

1 Answer

1992 Hitachi 60" Projection Television 60SX2K i was given this tv and was told that it just needed a bulb but i cannot find anywhere with a replacement part and want to know if it worth the money to...

The CRTs for this model are no longer available. Make sure that the CRT is the problem. If so, the set is not fixable unless you can find a servicer that has a CRT from old stock.


Jun 18, 2008 | Televison & Video

1 Answer

Hitachi 51GWX Scrambled Picture

STK392-560 STKS convergence CHIPs Replace both of them.

Feb 24, 2008 | Hitachi 51GWX20B 51" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

Cindy Wells

Level 3 Expert

6046 Answers


Level 3 Expert

85206 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides