Question about Whirlpool GEW9250 Electric Dryer

1 Answer

Dryer quit running in mid cycle

Stopped dryer to take something out. Attempted to re-start dryer ... will not start. Everything lights up proper, but when you press start, it beeps once and the "Sensing Lights" begins to blink. This all the machine will do. Have unplugged and cycled the breaker to no effect.

Posted by on

Ad

1 Answer

It's the thermal fuse and it's easy to install if you have a front loader just take the kick panel off in front, make sure you remove the lint filter and the cover that goes up to the lint collector and you will see the thermal fuse. Make sure you unplug before doing this. Take the two screws out of the bottom of kick panel and than use a putty knife and push down and the panel will come right off. Hope this helps you out.

Posted on Jan 16, 2008

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my Whirlpool Senseon Dryer start? The control panel will not respond. No buttoms will light up or beep. The dryer has power and the door latch works properly and the light comes on inside


Always disconnect power before attempting any service. Most electric dryers require 240 volts to operate properly.
You may have only 120 volts to supply the dryer which will give you your symptoms. Click dryer circuit breaker off then back on to reset 240 volt system.Still no heat/run
This link will aid you in tear down / diagnostics/parts
https://www.repairclinic.com/RepairHelp/Dryer-Repair-Help

I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

Nov 21, 2017 | Whirlpool Dryers

1 Answer

Dryer won't start - only beeps


If this unit has a timer it could be faulty. Make sure with the schematic in hand that all the wires are in the right spots on the motor. I did not post the model number so I am not sure what model you have but looks like a Whirlpool part number. If motor was running before you attempted to remove blade, this is a good one. If the motor relay is clicking but not turning that is almost like power is not were it should be. You can contact me here or reply to FIXYA with a response. Click here http://apcoappliancerepair.wordpress.com/?s=dryer+motor to see posts on dryers. I wish I could be more help. The first place I would start is with a schematic.

Apr 30, 2013 | Dryers

1 Answer

Hi, we have a Siemens IQ300 Condenser Tumble Dryer which we have recently inherited. Unfortunately it worked for a wek before just stopping. The lights are on and everything looks normal but when you


Check to see if it is properly grounded and that the incoming voltage is correct (120V or 240V) for the wiring config you have.on the dryer as it sits. Also try unplugging and wait a minute or so before plugging back in. This will sometimes reset dryer electrical components to factory settings.

Dec 07, 2012 | Dryers

1 Answer

Frigidaire dryer faqe7001lw blinking lights


Try resetting the computer like a cars e.c.m. by turning the dryer on and plugging it from the outlet. It worked for me once w our new Malta front loaders

Apr 07, 2012 | Frigidaire FAQE7001LW Dryer

1 Answer

After choosing dryer cycle by turning the selection knob, I try to start cycle by pressing big Start button. It beeps several fast beeps. Also the drum light just stopped coming on.


Hi,

There can be many reasons why your dryer will not start or turn...


The most common causes are the belt breaking or jumping off, or the motor going bad...

Here are a couple of tips that I wrote will help you to figure out why your dryer will not run...

Dryer Repair - The Dryer is not Turning
https://www.fixya.com/support/r4422207-dryer_repair_dryer_not_turning

Dryer Repair ? The dryer will not start
https://www.fixya.com/support/r4460438-dryer_repair_dryer_will_not_start


heatman101

Aug 20, 2010 | Whirlpool GEW9250 Electric Dryer

1 Answer

I just installed a new Kenmore Elite HE5 Steam clothes dryer. Everything powers up. Cycles can be selected and adjusted. However when pressing the start button, the button beeps 3 times and the dryer...


remove front panel and look at tec sheet inside / it will tell you what is not working . make shure all the packing has been removed and power cord is proper .. 3 beep are a code . tec sheet will tell .. mm .

Nov 24, 2009 | Refrigerators

1 Answer

Kenmore Elite HE3 Dryer (3 yrs. old)


when u push the buttons do all lights light up if so ,, machine is in lock mode ,, press and hold the little icon that read lock for about 3 seconds unitll lights are off then run ,, let see

Nov 19, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Dryer will not start, but does have power. The light and heating element are working, but the drum and blower are not functioning? Door switch is working properly, and there were not any previous...


The components to check include the motor's start switch & capacitor, if so equipped, the push to start switch, & all associated wiring. Check to see if motor & drum turn freely. Does the motor hum when starting is attempted?

Jul 15, 2007 | Roper RES7646KQ Electric Dryer

Not finding what you are looking for?
Whirlpool GEW9250 Electric Dryer Logo

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dryers Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

239 Answers

Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...