Question about Kenmore HE2 Plus Front Load Washer

1 Answer

I have a He2 plus model 110.47532601 with bad rear

I have a He2 plus about three years old to the day. It is model 110.47532601 with bad rear bearings.I also don't know who made it ie
Whirlpool, Electrolux. I thought the manufacturer might have some info?
Cannot find where to get the bearings or a schematic online to see what I need to fix it. Sears as usual, only offers the whole rear tub assembly for $330.00. I don't know if the bearings are pressed in or if there is a seal there that needs to be replaced? Any ideas or Help with this model?

Posted by rickgall1998 on


1 Answer

Richard Lilja

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 401 Answers

Hello Rickgall1998,
If t is a rear bearing (no symptoms listed) I doubt at 3 years old the bearing can be bad! I can't help you but if it is the door seal or some other common part perhaps you can find it here;
Kenmore Washing Machine Model 110 47532601 11047532601 110 47532601 Parts
Without some symptoms being listed it is hard to assist you.
Good Luck!
Rich Lilja

Posted on May 22, 2017


4 Related Answers


  • 1028 Answers

SOURCE: Kenmore HE2 Elite is making groaning noises and then error messages 5D and/or F

did you clean pump out by removing acess port on front end of pump? also you can ckd pump impeller by removing screws around pump body impeller will free wheel but should have some resistance to turning by hand if no water in tub reinstall pump put in drain spin to see if drum will spin if it does forget main motor ..motor is most reliable par on those washers

Posted on Aug 07, 2008



  • 1 Answer

SOURCE: torn door seal on front loading washer

My husband used super glue on the tear and for now the washer is not leaking.

Posted on Mar 26, 2009


  • 351 Answers

SOURCE: Can't locate stacking kit for HE2 Plus Washer and HE2 Dryer

more of the model number would help, but i can get them parts for you at feel free to give us a call

Posted on Jun 23, 2009



  • 15935 Answers

SOURCE: Error F28

F28 is a serial bus error from the CCU (Central Control Unit) to the MCU (Motor Control Unit).

All you need is some Electronics contact cleaner spray and a 1/4 inch socket to remove the top of the machine and the back of the machine.
The CCU is the computer looking box at the top front right hand corner.
Find connector M13, (has red marking on it and only 3 wires) disconnect it by pushing the retainer tab back and pulling gently on the connector.
Spray the contacts of the connector and computer with connector cleaner.
Then re-assemble connector.
The MCU is in the back lower left corner.
Find the connector with 3 wires and red mark, and remove this connector in the same way you did the other, spray it and re-install.
Put the back and top back on.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 11, 2010

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Are my washer and dryers able to be stacked?

if they are both front load, you can stack them, but you probably will have to have a special stand made, and a ladder to reach the controls. If you have a HE front load washer, it would not be worth stacking, because it will break and it will be harder to repair. But most likely you will buy a new one once you find out how much it costs to repair a HE front load washer. They may save water, but they run twice as long and do not clean as good and will break and the repair will cost likely cost as much as the washer. Either a circuit board will burn up or the rear bearing will go bad. The larger capacity the faster the bearing will wear out. If you just bought it, I would send it back and buy a top load commercial machine or front load, but not in a box store. I got 28 years from my old model and my dryer is over 30 years and never had a problem and still looks new. If you get 5 or 10 years from a front load, consider yourself lucky

Aug 20, 2014 | Kenmore HE2 Plus Front Load Washer

1 Answer

I have the Kenmore HE2 Washer Model 11046462501 - what is the capacity of this model and what year was it manufactured?

Hi from retired Englishman in SW France,
You should find that information on the manufacturer's panel on the back if there is no indication in the manual ;-0)
Cheers, John C

Apr 04, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

I just replaced the door latch on my kenmore front loader washer model 11047532601 the door locked light doesnt come on and the door locked light isnt coming on all i get is beep beep beep


You have a bad CCU. This is the control board on the top of the unit. Remove the top, three screws on the back. The board clips into the position. You can try to unplug the wires one at a time, the control will probably have to be replaced.

With the model I would be able to better assist you.

Mar 31, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

I have a Kenmore HE2 front load. It is blinking F-01. I tried pressing reset twice but it only lets me hit it once then everything goes off. Thanks

I have an old machine almost 30 years old and don't have these problems it is a simple machine with knobs. After all these years still works good.

Jun 29, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

My washer vibrates like crazy

Make sure it is perfectly level. If it is, you may just have a weak floor in your new place?

May 21, 2010 | Kenmore HE2 Plus Front Load Washer

2 Answers

What does code F21 mean on a Kenmore HE2 plus washer 11047532602?

it stands for longer than normal drain interval,press "pause/cancel" twice to clear, if it returns then look for obstructions in the water drain from the basket all the way to the drain in the house,or possibly it could be a bad washer drain pump

Nov 19, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

My washer will not drain. I get what looks like an F2 error message I have followed the manual instructions to restart the machine ... hitting "second rinse" etc. Nothing. This machine is not old at all...

There should be three screws in the bottom panel of the washer. Remove the screws and the pull panel down and off. There should be a clean out drain on the pump - so,'re gonna need a bucket. Hope this helps...(and good luck).

Nov 17, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Can't locate stacking kit for HE2 Plus Washer and HE2 Dryer

more of the model number would help, but i can get them parts for you at feel free to give us a call

Jun 23, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Blow breaker

I need the model n serial # to better assist you.

Thank you

May 10, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

When in spin made loud klunking and screaching noise. now will not work in spin cycle without making loud klunking noise

Pull off the bottom panel, (three 1/4" screws along bottom). Check for chunks of concrete hanging down, or in the bottom pan. I have seen the lower front counter-weights on the HE2 break off several times. If not, reach in and give the basket a hard spin by hand, if you hear clunking or grinding, or the basket feels loose, you have a bad basket brace (usually caused by slop in the rear bearing). You would need to replace the rear shell (comes with a pre-installed bearing) and the basket. Depending on age, these parts may be in warranty, check your manual.

Apr 20, 2009 | Kenmore HE2 Plus Front Load Washer

Not finding what you are looking for?
Kenmore HE2 Plus Front Load Washer Logo

Related Topics:


Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Paul Carew

Level 3 Expert

3538 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides