Question about Sony PlayStation Portable (PSP) Console

1 Answer

Sony playstation

How to take out the circcuit board on the right keypad because buttons do not work

Posted by on

  • Anonymous Jan 06, 2009

    no puedo pasarle videos al psp

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 263 Answers

Http://manuals.playstation.net/document/en/psp/current/photo/mscopy.html

Posted on Jan 04, 2008

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced control board and keypad but oven buttons still not working


I pulled the schematic there is a thermal fuse on the neutral wire going to the control you should have 120VAC at terminals P4-3 and P4-1 if not find the fuse back trace from P4-1

Feb 12, 2014 | Whirlpool Ovens

Tip

How to fix a remote


If your remote don't work out in some keypad/button only then maybe the possible problem are:

  • on the keypad/button maybe it is little bit hard or soft to press.
  • maybe the keypad/button has a short pointer inside the keypad/button so that it cannot reach the board.
  • or the keypad/button just can't reach the board because it is not in exact location.
  • the board has an ashes so it does not work.

Regarding those problem above you need to do/apply the steps below.


1. Open the remote by unscrewing the back cover of the remote.
2. Then you will see the remote control board ( the remote
control board is the one with lots of many circle,colored: black
with green) try to remove it slowly.
3. Then find any cotton thing like cotton buds and also four pieces
of small hard paper.
Clean the internal remote control board using the cotton
material/cotton buds.
4. Then try to have/put a thing like a small four pieces of hard paper
inside,underneath the board in both four sides (it should be balance
by each other side) of it then try to see if the keypad/button is
being reach by it.
5. Then if done, when assembling it make sure that the board is well
done/place in the right position and exactly in the front of its
assigned value/number.
6. Then when done assembling try to test it in actual if it works.


I hope this steps could be helpful..If not maybe the battery is old enough to use and need to replace for a new one or some connection near the battery has cut off, if it is the problem just contact me for some/other solution..If this solution helps you I would be very glad to here it!! Thank you!!

on Jun 06, 2011 | Televison & Video

1 Answer

The middle button of my motorola wont work


dismantle and service that faulty button. Use PENCIL (as a source of carbon, because carbon is an electrical cunductor), Scrap the end of the button with that sharp pencil also the "circcuit" involved.

Jul 24, 2011 | Cell Phones

2 Answers

Tried to reprogram security code for outdoor key pad on 1/2hp craftsman garage door opener according to instructions online, pressed learn button- put in new 4 digit code-held enter. Lights did not flash...


Seems you've done everything right. Press and immediately release the smart/learn button and then walk over and key in a 4 digit code and press enter. If you are sure the battery in the keypad is good then I think your keypad is on the fritz or the wrong one for that opener.

Apr 19, 2011 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

The down button the numbers 2, 3 and end call button have stopped working. when i press one of these buttons its shutting the phone down-any ideas or advice please?


Hi, it's the keypad IC or the keypad itself. So you can check the keypad if there is dirts that is stopping the keypad from working. Or the keypad needs to be replaced.

After checking the keypad if the keypad still did not solve the problem,
You will have to replace the keypad IC inside the board of the phone.

Take care. .

Aug 20, 2010 | Sony Ericsson K850i Mobile Phone

1 Answer

Keypad doesn't work onlt the on/off button


hmmmm... maybe a one of the side buttons is stuck up..try pressing them if all side buttons click, if not then there's your problem

Jan 24, 2008 | Motorola Mobility RAZR V3xx Cellular Phone

2 Answers

Keypad


open it ang change if u dont want to change open keypad circuit and clean it with eraser.I AM SERIOUS.

Nov 24, 2007 | Motorola Mobility RAZR V3

1 Answer

Microwave


Having the brand and model will help us point you to the parts supplier so you can buy a new keypad.

Please post back.

Oct 23, 2007 | Microwave Ovens

Not finding what you are looking for?
Sony PlayStation Portable (PSP) Console Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Video Game Consoles & Games Experts

Ekse

Level 3 Expert

13434 Answers

shevantha perera

Level 2 Expert

125 Answers

Damen Wong
Damen Wong

Level 3 Expert

1950 Answers

Are you a Sony Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...