Question about JVC RX-6010V Receiver

1 Answer

Little or no sound JVC RX6010V

Little or no sound: I have minimal volume coming through from TV or DVD on my JVC RX-6010V receiver. I have recently connected a digital cable box to the system and now have volume through the radio and CD player, but very limited volume through the TV or the DVD player. I can turn the volume knob all the way up to 80 and the volume is low.

Posted by on

  • garry1943 Jun 04, 2008

    no sound from tv but am and fm work fine

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem but i went to adjust settings and it says right speaker left speaker and you have to set them on ten

Posted on Apr 14, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I connect a turntable with RCA cables?


You can't. There is no provision for a turn table on this model receiver.

Oct 20, 2014 | JVC RX-6010V Receiver

1 Answer

JVC 6010V shows zero on volume wont go up or down


This is a fault on the D/A digital / Analogue converter , The volume control being analogue is not processing the data in the cicuit and so there is no change in the level. This can be a fault in the IC - the D/A convertor IC which is not giving any response with the turn of the potentiometer. So check this within the amplifier ONLY if you are able to trace the circuit and replace the IC connected to the potentiometer.

Oct 21, 2011 | JVC RX-6010V Receiver

1 Answer

I have a JVC RX 554v Receiver when it's turned on I have no sound their is a mute auto light that's lit in the window....Tried changing the speaker wires with no results...


From the remote control only: Press MUTING to turn off the sound through all speakers and headphones connected. "MUTE" appears on the display and the volume turns off. To restore the sound, press MUTING again. Turning MASTER VOLUME or pressing VOLUME +/- also restores the sound.

Sep 01, 2011 | JVC RX-554V Receiver

1 Answer

I have this JVC RX-6010V Receiver, how can I connect my microphone to the unit?


Get a microphone (with a) preamp and follow ITS instructions. It only accepts RCA Line Level analog signals.

Jul 05, 2011 | JVC RX-6010V Receiver

1 Answer

My JVC receiver won't play my left front speaker. The right one seems to work fine but when I plug in the left it is virtually silent. i too have had a few "overload" incidents and am running two JBL 8...


swap the wires around to see if the right speaker will give sound on the left channel. If it does, the it's a blown left speaker. If you don't get sound out the right one either, then the left channel ouput has a bad capacitor somewhere in it.

Jul 06, 2009 | JVC RX-6010V Receiver

3 Answers

My jvc rx-6010v is OVERLOADING?


The very FIRST thing to check is to make certain ALL of your speakers have an IMPEDENCE of 8 OHMS. (JVC - and others - say SIX ohms, but 8 is the "standard" you should use.) Virtually all speakers of even modest quality will include this specification on a label on the back of the speaker. You CANNOT run more than (2) TWO speakers with 4 OHMs impedence on ANY amplifier (technical discussion too long!) [NOTE: The internal overload protection system you mention is designed to help prevent permanent damage. However, you cannot re-set these systems yourself. Your dealer or authorized JVC service center must do this. Note, though, that if you have attempted to "cheat" the system several times, damage CAN be done that requires servicing.] But, before you take the unit in for service, there is one more "test": check for shorted and/or mis-connected/disconnected speaker cables/wires. Visually inspect connections at the receiver and speakers first. You might find something obvious! If everything looks okay, then disconnect ALL of the speakers; and reconnect and test them one at a time (at relatively low volume.) For example, reconnect the left front speaker, test the system; THEN add the right front, test the system,and so on, ADDING one more speaker each time - FIRST MAKING SURE EACH OF THEM HAS AN IMPEDENCE OF AT LEAST 8 OHMS! IF there is a short (or bad speaker) this will help isolate it. Hopefully one of these "fixes" will work for you. GOOD LUCK!

Jul 10, 2007 | JVC RX-6010V Receiver

Not finding what you are looking for?
JVC RX-6010V Receiver Logo

Related Topics:

870 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76171 Answers

stynger007

Level 1 Expert

33 Answers

Are you a JVC Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...