Why does it not follow the story right

Printer contain 4 cartridges and 2 printeads. Because the black color skip some lines as you mentioned you need to replace a new printead(not the cartridge) No:88 Black/Yellow color one. For more information visit the following link: http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=&cc=us&docname=c00841890&product=2512009

Sounds like the cartridge connector inside your Sega Genesis is dirty. You'll need to clean the connector AND clean all of your cartridges with rubbing alcohol. Cleaning this connector should be no big problem. Make sure your Sega Genesis is unplugged before you try any kind of cleaning or repair.

To clean your cartridges, simply use rubbing alcohol and Q-tips to scrub the connector pins clean. You will notice lots of dirt coming off onto the Q-tips. This will take many Q-tips.

This is important! Once you clean your cartridges, you still need to clean the connector inside your Genesis. Here's how:

First, get a can of compressed air. Blast air into that cartridge connector to remove any loose dust, dirt, or debris. Chances are, you'll still need to clean more.

Second, Use Q-tips to apply rubbing alcohol to one of your clean cartridges. Insert and remove this cartridge repeatedly.

Third, dry off your cartridge with clean q-tips.

Repeat steps two and three over-and-over until your cartridge slot is clean. Remember to give your Genesis time to dry before you plug it back in.

Bonus tip: If the above method doesn't get your connector totally clean, try wrapping a thin piece of cloth around an old credit card. Apply rubbing alcohol to the cloth, and scrub away at the cartridge connector.

Forgive me if this sounds condescending, but it bears repeating. Please make certain to unplug your Genesis before you attempt to clean or repair it. Safety first.

try to reinstall the game. it sounds like theres a problem with the installation files

try cleaning the little contacts on the cartridge, and where it mates too...sometimes this will "Fix" it.
link below for you to get a manual to help.
http://printer.konicaminolta.com/support/current_printers/mc2430dl_sup.htm

This sounds like you need to replace the ink cartridges. Stuff is missing because the ink is very low or empty. Also, if you have just replaced the ink cartridges then you might need to do a cleaning cycle on the printer.

just play normal and your in story mode

1Become the Venom character by pausing the game and entering the following code using your joystick: O X X O O O Triangle X Square O. Gain infinite health and become invincible by entering cheats when you're in pause mode. You gain infinite health by tapping the O button on your joystick 10 successive times while the game is paused. Put yourself in a black Spiderman costume by entering the pause mode and pressing X O X O Up Up Down Down. When you un-pause the game, your character will be dressed in black from head to toe. Use game cheats to become the Green Goblin character. This is done by entering the word "Deadly" on the Cheats menu. Give yourself the added advantage of "super strength" by holding down the R1 and L1 buttons on the game's title screen. While holding them down, press O O, then tap the R2 button. You'll begin the game with super strength. Play Spiderman 3 as Stan Lee by pausing the game and entering the following button combination: Select Up Down Triangle Triangle O X X O R2 R1 L2 Left Left Up Right Down Circle Triangle Circle. Whew. Then save the game, turn off your PS2, restart it, and load your saved game. Repeat the same cheat and presto! You'll appear as Stan Lee, the creator of Spiderman. Get everything for free in the game by going to the game menu when you begin your session and holding down R1 R2 L1 L2 all at the same time. This will open the cheat menu. Enter "FREEALL" to get everything free. Step8Use the cheat menu to unlock all the game's Easter eggs and secrets by entering the word "VENOMSKY."

"You forgot the "first rule , check to see if everythings is working! If the filter was dirty , then you skipped the second line of defense to prevent dust from going into the vents is the squirrell cage blades. Air flows thru the filter first,,,2ond, thru the squirrell cage...& 3rd thru the coils last. Make sure the outside is working fine.

well..did you run a test page?

or clean the print heads?

or recalibrate them?

recommend all these steps for you

and as my 2200th solution, you are entitled to a FREE tuneup for good. find out more about that service here

please you change the incoder strip.your problem was solved