I am getting an F2 error code on an DD603. - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Sharp ARM316 - Error Code: F2-02

PrintCopy .info https://printcopy.info > model=ARM316 > code=F2-02
Code: F2-02; Description: Toner supply failure. The value judged from the actual toner supply hysteresis differs greatly from the toner sensor value.
Missing: photocopier. ‎' Must include: photocopier.

• 
  

  Sharp ARM355 - Error Code: F2-02

  https://printcopy.info > brand=Sharp > code=F2-02
  Code: F2-02; Description: Toner supply abnormality. Toner control sensor output value becomes under-toner too earlier. Causes: Connector harness trouble ...
  
  Generic video
  
  

http://printcopy.info/?l=en&mod=erc&brand=Sharp&model=AR5623N&code=F2%2070

Sharp AR5623N Error Codes

Sharp AR5623N Error Codes Code: All codes CH Blink CH ON E7 01 E7 02 E7 06 E7 10 E7 11 E7 16 F2 40 F2 64 F2 70 F2 74 H3 00 H3 01 H4 00 H5 01 L1 00 L3 00 L4 01 L4 31 L4 32 L6 10 U2 04 U2 11 U2 12

Code

F2 70

Description

•Improper cartridge (Destination error, life cycle error) •Identific t ion error •Model error •Type error •Destination error •Data abnormality •Misc error Detail •The destination of the machine differs from that of the CRUM. •The trade mark code of the CRUM differs. •The company code of the CRUM differs. •The boot program model code does not coincide with the CRUM model code. •When the CRUM type is other than genuine/ conversion/production rotation. •The machine destination differs from the CRUM destination.

Causes

CRUM chip defect Improper toner cartridge.

Remedy

Replace the toner cartridge.

Hi - F2 error code indicates a failure of the rotor/motor or the sensors, the following notes should give you guys something to check and see which of these has failed..

Error Code - F2

Which LED - Delicate LED

Reasons - The motor has not been sensed rotating

Likely Causes

_ Foreign object has jammed the rotor

_ The rotor has failed

_ The hall sensor has failed

_ The electronic controller has failed

Hi there,

Well F2 error codeis on a variety of Sharp copiers, the F2 error code would normally be accompanied by a sub code that indicates the fault, You may please check out the following -

• F2 with sub code 00 - Toner Sensor problem, ID pattern reading error;
• F2 with sub code 02 - Toner Motor problem, check toner dispenser motor;
• F2 with sub code 31 - Image Density error, Check the light level or the drum surface reflectivity;
• F2 with sub code 32 - Drum Mark sensor, missing/dislocated mark or sensor faulty. Sensor cannot scan mark properly;
• F2 with sub code 33 - grid voltage wrong, either too high or too low;
• F2 with sub code 35 - grid voltage correction will not work during simulation;
• F2 with sub code 37 - drum mark sensor adjustment required.

You may post further comments for more help or information......

Good Luck!!

Thanks for using FixYa!!

Maybe you dont have to remove anything else.. try the rotor from the bottom drawer first. If this works just buy a new rotor..

Hi,
Below is the link. Although it is for the DD601v2 the DD603 follows the same principle.
http://www.scribd.com/doc/6462163/DD601V2-Manual
Mat
Please rate me

Sharp AR-5620N getting f-2 error. What is the solution

You can get fisher paykel service manuals here:
http://fisherpaykelparts.net/index.php

check your email

This is information from the Tech Sheet.

Fault Code F2 - Error Code E1: Code Explanation: Keypad keytail not connected. Recommended Repair Procedure: 1. Check keypad connector for firm connection. 2. Press CANCEL. If error code returns after 60 seconds, replace keypad. 3. Replace control.