The display says following output tray is full.

To re-attach the output tray long piece on the Ricoh SP C360DNw, follow these steps:

1. Turn off the printer and unplug it from the power source.
2. Locate the output tray and the long piece that needs to be re-attached.
3. Align the long piece with the slot on the output tray and gently push it in until it clicks into place.
4. Turn on the printer and check if the error message has disappeared.

If the error message persists, try removing and re-installing the paper tray to ensure that it is properly seated. If this does not resolve the issue, there may be a problem with the sensor or other internal components of the printer, and it may require professional servicing.

The error code 22550 on the OCE ColorWave 650 indicates a "Paper Jam in Output Tray".

This error typically occurs when paper or other debris becomes lodged in the output tray or the paper path leading to the output tray, preventing printed pages from exiting the printer.

To clear the error and resolve the issue, follow these steps:

1. Turn off the printer and unplug it from the power source.
2. Open the output tray and remove any jammed paper or debris.
3. Check the paper path leading to the output tray for any obstructions or debris, and remove them as necessary.
4. Close the output tray and turn the printer back on.
5. Try printing a test page to ensure that the error has been cleared.

If the error persists, there may be a mechanical issue with the printer that requires service from a qualified technician.

1. Remove paper from all output trays. Depending upon the options fitted to your device, the output trays are:
• Internal Tray 1 (basic configuration)
• External Tray
• Internal Tray 1
• Internal Tray 2
• Upper Tray - 1000-sheet Finisher
• Shift Tray - 1000-sheet Finisher
• Shift Tray 1 - 2500-sheet Finisher
• Shift Tray 2 - 2500-sheet Finisher
• Upper Tray - Booklet Finisher
• Shift Tray - Booklet Finisher
• Booklet Tray - Booklet Finisher
2. Locate the gray cables that are connected between finisher and main unit. Check that they are secure, and that the cables are in good condition.
3. Switch off the device at the red power switch.

Print a self-test report Use the following steps to print a self-test report.

1. Load plain white paper in the input tray.
2. Press Setup , and then press 2 . The Print Report menu displays.
3. Press 1 to select and print a Self-Test Report .

IMPORTANT! Try to print a self-test report after every solution even if the solution resolves the issue. Solution one: Clear the paper jam Follow these steps in the order presented to resolve the paper jam. Step one: Remove loose paper from the tray Remove any loose sheets of paper from the input tray and the output tray. CAUTION: Do not remove jammed paper at this stage. Trying to clear jammed paper from the front of the product can damage the print mechanism

Check the little black piece of plastic that senses the printed page exiting the machine. Our sensor was stuck and I was getting the same message (an similar Ricoh product). When I gently reset the black piece to center, moving freely, printing worked again. I think the sensor got jammed up when we were trying to remove a bad paper misfeed.

Ricoh manuals very confusing on this error message. They refer to standard tray, tray one, etc. without being clear whether it's a paper feed tray or the so-called "standard OUTPUT tray." The output is not really a tray, it's just the depression where your sheet lands after printing. I wrenched on the paper feed trays and their settings for an hour before I figured out they meant OUTPUT.

Please you must remove the copies from the output tray.
If you don't have copies in the output tray, check for a black lever at the middle of the exit rollers. It can be either stucked or broken.
If you want this lever can be folded inwards.

Good luck and please rate me, thanks.

Hi,
If you look at the paper exit you will see 4 white exit wheels
in the middle of the 2 center ones you will see that there is a black
lever. This needs to be pushed back into position so that it is horizontal to the exit wheels.
Hope this helps regards
Myott

hi im jules_09,there must be a small piece of paper stocked at the output tray.see if you can open the front door then full out the fusing unit somtimes paper is stocked in it.then while the fuser or fusing unit is out check the output tray if there is a paper.in the fuser unit check the hotroller or upper roller its a black metal roller that heats up

Hi, there must be an actuator of the output tray sensor.It is placed above paper tray, just in place when paper exit from machine.Try to clean sensor,or to place actuator in proper place-pull it down.Also,maybe is actuator broken.