Question about Yamaha 2500 Watt Industrial Inverter Generator YG2800i

1 Answer

Running at idle speed - Yamaha 2500 Watt Industrial Inverter Generator YG2800i

Posted by nnoditony on

  • Anonymous May 11, 2010

    What do you mean???????????/

×

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 148 Answers

1) Check the "Economy Throttle" setting (or some similar verbage). Inverter types dont have to run full speed to produce full voltage.

2) Apply a load. These magically accellerate and decellerate according to load conditions.

Hope this helps,
Dolf-

Posted on Oct 13, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my car cuts off when i get off of the asellorater


Could possibly be the speed sensor malfunctioning. Have it checked or just run the idle screw up a couple turns for now to keep it running. Once it keeps running, turn the screw back out to a proper idle. And sometimes it's the AC speed up solenoid not working to raise the idle when AAC is on.

Mar 25, 2018 | Cars & Trucks

2 Answers

2003 Kia Sedona what is the RPM supposed to idle aton cold start an in warm weather


Idle speed depends on a number of factors; for instance it may idle faster when the air conditioner is on. Instead of a fixed idle speed, as in the old cars, the engine computer sets the speed to whatever is needed to run any accessories and maintain smooth operation, but generally not more than that. That's under normal circumstances. There are several failure modes that cause erratic idle speed; usually the engine will also run roughly.

Jul 09, 2017 | Kia Cars & Trucks

1 Answer

It idles fast if I turn the idle down it stalls running rich on top end at fast idle sometimes it will drop to a very low idle and shut off


adjust the idle mixture screws first and then adjust the idle speed screw to compensate
adjusting the idle mixture screws will alter the idle speed but when properly adjusted then adjust the idle speed screw,

Aug 24, 2015 | Motorcycles

1 Answer

Engine speed decrease when stert the AC


IDLE AIR CONTROL VALVE IDLE SPEED TOO LOW. IDLE SPEED SHOULD BE 750 - 850 RPM. IDLE SPEED NEED TO BE CORRECT OR IT WILL CAUSE ENGINE RUN ROUGH OR STALL OUT.AC COMPRESSOR WILL TAKE SOME POWER FROM ENGINE WHEN AC IS OPERATING.

Jun 12, 2011 | 1995 Kia Sephia

2 Answers

Trying to adjust the idle speed. running at 1500 instead of 1250 rpm


The idle speed is controlled by the bikes computer, the ECU. The 1500RPM idle is normal. If you purchase a Race ECM from Erik Buell Racing (http://www.erikbuellracing.com) you can get one with a slightly lower idle programming. The bike does not like to idle low, hence the 1500RPM stock idle.

Apr 28, 2011 | 2008 Buell 1125R

1 Answer

Starts, idles and runs but quits after a few seconds of cutting


Check the air cleaner and muffler for plugging. One screw adjusts the idle stop (idle speed) position and the H and L jet screws set fuel mixture for high speed and idle speed mixture respectively. Turn both jet screws CW to stops (lightly) then back each out CCW 1-1/2 turns. This is a basic setting and should allow the engine to start and run. Start the engine and allow to warm up. Pull the throttle full on and adjust H CW until the engine starts to speed up, but 4-strokes. Correct adjustment is when the engine 4--strokes running free, but immediately 2-strokes when cutting. Release the throttle and adjust L needle CW until the engine idles fairly well, but allows the engine to 'follow the throttle'. Adjust the idle speed screw so that the chain stops turning, but the engine will continue to run. Hope this helps!

May 17, 2010 | McCulloch 16 Inch Gas Chain Saw MCC1635AK

1 Answer

My bike runs rough idleing and at slow speeds. It


Check for intake leaks where the carburetor manufolds connect to the heads, when it is running at idle dpray WD40 around the area if the idle increases there is a intake leak.
reolace the gasket/gaskets,and since the carb will be off clean it or have a mechanic do it.

May 16, 2010 | 2000 Harley Davidson FXSTS Springer...

1 Answer

When I have it on it stays on high idle speed. When I push the auto idle it will not change the speed to normal. It idles at high speed all time.


If you have anything plugged into the generator, consuming any electric, it will run at high. It must run at high speed to generate 120V. It will only idle if your turn off the load.

Feb 13, 2010 | NEC Mitsubishi MGE 4000 Generator ROU...

Not finding what you are looking for?
Yamaha 2500 Watt Industrial Inverter Generator YG2800i Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Electrical Supplies Experts

Sheldon Dedek

Level 3 Expert

912 Answers

Dan Horsefield
Dan Horsefield

Level 2 Expert

287 Answers

Robert Wooley
Robert Wooley

Level 2 Expert

178 Answers

Are you a Yamaha Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...