Proscan PS27500 27" TV Logo

Related Topics:

Question about Proscan PS27500 27" TV

Open Question

Kishu tv turned off at the wall,it will not turn back on,apparantly theres a reset button some were,but were

Posted by ronnie_broom on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why wont my sharp lcd LC-32D44U turn on?

Well, there could a be few issues. First thing is to verify the breaker that gives power to that wall has not tripped off in the home's break power panel. If it is not tripped then verify the wall outlet that the TV is plugged into has a reset button, like a GFI (ground fault interrupt) If it does then verify that it has not tripped. If the GFI on the wall plug is tripped simply push the reset button back in and then try plugging in your TV power plug again. Then if that checks out or does not have a GFI outlet, verify that the power plug going into the back of the TV is not loose. Unplug and replug power plug that plugs into the back of the TV in and verify it is securely connected. Lastly, the power supply in the TV might have gone out.
0helpful
1answer

My tv has full picture for about two minutes thengoes blank the green light blinks then comes bak on and repeats the process

You have to reset your tv.
If there is no reset button,then while the tv is on unplug the cord from the wall socket,this shouid reset the tv.Wait about 5 minutes before you turn it back on.
If this doesn't work then,your tv is about to go,unless you have a valid warranty.
Hope this helps.
0helpful
1answer

Where is the reset button

There is no reset button. To make a hard reset, just unplug the set from AC mains wall socket, and re-lug it back after 20 minutes or so.
0helpful
1answer

Sony kp-65wv600 projection tv error code. My tv blinks 7 times.

Hi,
The Standby LED blinks when the TV is turned on, then shuts off when the picture is displayed. If the LED blinks continuously, this may indicate that the TV requires service. Before getting the TV serviced, try power resetting the TV and factory resetting. Try the below steps also: Connect the TV to a different wall outlet and check if it helps. This is to check if the issue is with the Power. Disconnect the TV from the Power Strip or the Surge Protector and connect it directly to the Wall outlet and check if it helps. To Power Reset the TV, disconnect the Power cord for a short period of time (approximately 1 minute). Then, reconnect the Power cord and power ON the TV. To factory reset the TV, turn it ON. Then while holding down the RESET button on the Remote Control, press the Power button on the TV front panel. The TV will turn OFF and then turn ON again. Then release the RESET button to complete the reset procedure. If the issue persists, service may be required.
Good Luck!!
0helpful
1answer

When we turn the tv off with the remote, we have to unplug the tv from the wall to reset the tv so that it will turn back on. Once we turn off the tv, it will not power back up with the remote or with the...

The power supply board is the cause.That the board,where the power a/c cord plug into it.Tries website like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.
0helpful
1answer

TV went off, standby timer light flashing

Try unpluging from the wall and theplug back in and try turning back on to reset. Sometimes holding the power button in while pluging back in will reset it, every brand is different for the hard reset.

Scott
17helpful
3answers

How to reset hp 6310 printer

Hi,

The below are the 4 Types of Resets.

Power Drain
:

  • Turn OFF the printer, disconnect the power cable from backside of the printer and from wall outlet.
  • Press and hold the Power button for 60 seconds.
  • Connect the cable and turn ON the printer.

Partial Reset

  • Remove the power cable from back side of the printer while its ON.
  • Press and hold "#" and "3" button, while holding them both insert the power cable and release the button after 10 seconds.
  • If printer turns OFF, press power button to turn it ON.

Semi-Full reset


  • Remove the ink cartridges.
  • Remove the power cable from back side of the printer while its ON.
  • Press and hold "#" and "6" button, while holding them both insert the power cable and release the button after 10 seconds.
  • If printer turns OFF, press power button to turn it ON.
  • Insert the ink cartridges.
Full-NVM Reset:

  • Remove the ink cartridges.
  • Remove the power cable from back side of the printer while its ON.
  • Press and hold "OK" and "Cancel" button, while holding them both insert the power cable and release the button after 10 seconds.
  • If printer turns OFF, press power button to turn it ON.
  • Insert the ink cartridges.

Regards,
Rizwan
1helpful
1answer

Button on TV does not turn on. Although there is power to the TV the on off button does not seem to engage. Television is a Centrex

try unplugging tv from wall. wait 2 minutes. this resets the computer in the tv. then plug back in. good luck!
0helpful
1answer

Where is the button to turn off my technika dvd tv?

Apparently you can not turn it off, it always remains on standby unless you turn it off at the wall. Or maybe I'm just missing something as well.
12helpful
3answers

Displays E 01

Talked to the nice lady at West Bend. Apparently, the problem comes up when the unit is "cold"... whatever that means. She said to plug it in, wait a second, then push the power button, then "cook" immediately. No pause. Don't hold either button. I tried it, it worked on mine.

Apparently, this a feature for some reason.
Not finding what you are looking for?

98 views

Ask a Question

Usually answered in minutes!

Top Proscan Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Jaime Hernandez

Level 3 Expert

2351 Answers

Cindy Wells

Level 3 Expert

6553 Answers

Are you a Proscan Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...