Can you supply an instruction manual for a creda simplicity condenser dryer TCR2

The Creda Simplicity T620CW dryer does have a resettable thermal safety cut-out switch, which can trip if the dryer overheats. This switch is located on the rear of the dryer.
Here are the steps to access and reset the thermal cut-out switch on your Creda Simplicity T620CW dryer:

1. Unplug the dryer: Make sure the dryer is unplugged from the power supply before you attempt to access the thermal cut-out switch.
2. Remove the rear panel: The thermal cut-out switch is located on the back of the dryer. You will need to remove the rear panel to access it. Use a screwdriver to remove the screws holding the panel in place, and then slide the panel off.
3. Locate the thermal cut-out switch: The thermal cut-out switch is a small, rectangular device with two wires attached to it. It is typically located near the heating element or the exhaust duct.
4. Reset the switch: Press the button on the thermal cut-out switch to reset it. You should hear a click when you press the button.
5. Reassemble the dryer: Once you have reset the thermal cut-out switch, replace the rear panel and secure it with the screws you removed earlier.
6. Plug in the dryer: Plug the dryer back into the power supply and turn it on. If the thermal cut-out switch was the problem, the dryer should now work normally.

If resetting the thermal cut-out switch does not solve the problem, it is possible that there is a more serious issue with your dryer. In this case, you may need to contact a professional repair technician to diagnose and fix the problem.

new interlock then .....cheers

how to fix my t622cw because the drum will not turn round

Hi from retired Englishman in SW France,

I'm so sorry but this forum does not, nor is in a position to, supply any type of manual (service or otherwise), parts list, installation instructions, electrical or schematic diagrams direct; it's just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web ;-0)
Also members on Fixya are not 'affiliated' to, or representative of, any manufacturer at all, just using their experience gained probably over many years.

Manual
You will need to type into your search engine/web browser '(make model number) washer service manual' and you may be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct but often it will supply only to registered agents.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check outthis electric no heat tip...

heatman101

Hi,

If your dryer is not drying like it once did or if you just have nottaken the time to give yourself a clean dryer in a long time then youneed to do that. At least once a year the dryer cleaning should takeplace. Lint build up in the dryer duct is one of the main causesfor your dryer to fail.

Here is the rest of this tip about DryerMaintenance

heatman101

laundry.manualsonline.com/manuals/.../creda/w100fw_w120fw_w120vw.html -

It is going to be 1 of 2 possibilities.
1--A faulty start capacitor.
2--A slack or drive belt.
More likely to be the capacitor, located at bottom rear right of dryer looking from front.
It entails removal of top cover and right hand side panel to gain access
Please rate my solution.
Thanks.

There is a lint filter inside the front of the m/c.
A filter at the bottom left of m/c,undo catches to release it, remove it and wash out under running water to thoroghly cleanit.
.Remove water container at top left front , and empty.
Make sure air intake and air out lets are clear, one at front right, and one at rear of m/c.
You can download user instructions.
Goto;;
www.hotpoint.co.uk

Click on (after sales), click on download user instructions, and follow the guide

Plz rate my solution.
Thanks.

put it in the bin