Question about Kyocera FS-2000D Laser Printer

1 Answer

Error code 0159:0061914

Machine won't print, just displays the error code. Any help please.
Thanks.
Bruce

Posted by AussieTeck on

Ad

1 Answer

Soulvisitor

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kyocera Master
  • 1,113 Answers

I couldn't see a 159 error in the 2000d service manual, but I know 150 errors . They need to have their firmware updated, should be under warranty, their is a kyocera service bulliton on this issue so all agents can do your repair. It is just a matter of downloading firmware from kyocera. unzipping it to a mem stick or CF card and powering on your printer with it inserted, firmware then self installs.

The bits after the 159:is just page counter. Post Email if you want me to send you zippped firmware to suit.

Posted on Dec 22, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The printer wont printer and displays "Unable to Print. See Troubleshooting and Routine Maintenance Chapter in Users Manual"


Unplug the printer for about 15seconds and then plug back in and power up.......this should reset the error code! Test print and you should be good to go!

Oct 05, 2014 | Brother Mfc9420cn Mfc-9420cn Fax Modem...

1 Answer

I keep getting a F6E5 error code on my Whirlpool stove. I have tried unplugging it (overnight) and the error won't go away. Any ideas before I call the repair man?


The error code F6E5 means "Cancel key error". Press the "Cancel" and "Start" keys in the following order: CANCEL, CANCEL, START. Verify the error code displayed on the control by observing for longer then 1 minute. If the error comes back then the control board needs to be replaced..
If this was helpful please rate me Thanks

Jun 12, 2011 | Whirlpool Ovens

1 Answer

Error code 902.48 - won't print


Power off the machine and power it back on. Print a simple test page to determine if the problem is system software related or a corrupted print job. If the error is related to the corrupted print job, then there is no issue with the printer. If the error is not related to a corrupted print job and is believed to be system software related, Please call Lexmark Technical Support.

May 24, 2011 | Lexmark X342n All-In-One Laser Printer

1 Answer

Canon printer i865 Orange light blinks 5 times and the following message appears: "Operator error. Press printer's RESUME button. If this doesn't clear the error, cancel printing and turn the...


Dear Bruce,
Blinking in orange 5 times indicates that the print head of your printer is faulty. To ensure this you can compare by using another print head. But first,please remove the print head and check whether it is burnt. Some short circuitry may cause the problem. Thanks.

Source:
Printer Clinic

Dec 26, 2010 | Canon Office Equipment & Supplies

1 Answer

The exclamation sign flashes and then the green light but no printing


The service Manual says that if both the ready (Bulb) light and the exclamation light are both on it is a invalid engine
code /Invalid network code. But to clarify that you say they are both on and solid and not blinking. If they are you have a bad main board.
If they are blinking then the error is a Flushing /Resolution reduced error.
The cause is:
Printer is processing data or printing pages,but the resolution of a page in the current print job is reduced from 600 dots per inch (dpi) to 300 dpi to prevent a memory full error.
Solution is:
Wait until the ready light is displayed to print other jobs.
• Press and release the triangle button to cancel print job. It is the lower of the two buttons.
• Press and hold the traiangle button again to reset printer.
Hope this helps
Bruce

Jul 14, 2009 | Lexmark E232 Laser Printer

5 Answers

Riso ks800


e4-ink over flow. solution-clean ink sensor.
e3-clamp motor locked. solution-use code 64

Sep 21, 2008 | Office Equipment & Supplies

4 Answers

My canon iR3300 is displaying error code E000002-0000. Please help.


My canon iR3300 is displaying error code E000003-0000. Please help

Jul 30, 2008 | Office Equipment & Supplies

2 Answers

DISPLAY READS: 80 SERVICE (01E4)


If you keep getting 80 service, first recycle the power to the printer (try a few times if the error doesn't go). If that doesn't work replace the MIO card (the bit the network cable goes in)

Jun 16, 2008 | HP LaserJet 4 plus Printer

2 Answers

Brother Mfc 420cn says machine error AF


Open the small cover that hides the scanner flat cable. It has to be reconnected to the main pcb.

Oct 23, 2007 | Brother MFC 420CN All-In-One InkJet...

Not finding what you are looking for?
Kyocera FS-2000D Laser Printer Logo

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...