Atapi pioneer dvd-rom 115

check the jumpers are on master slave or both on CS Cable Select

Dial +1-800-204-4427 and Get end of support information for Windows XP and find out what you need to know to upgrade to Windows 10 or find a new PC.

If its the full windows xp cd by booting it from the cd drive it will erase everything and ask if you want to upgrade or advanced install I think. Your correct in choosing the atapi cd-rom as 1st boot device. The cd should be in the drive on startup. IDE is the type of hard disk drive. I'm guessing the FDD stands for floppy disk drive which you might not have that many but you have that many bay windows available.

Put disk in, shut down computer, Start computer and it should give you the xp disk contents. Be aware of data loss though.

Good luck.

The first edition of Windows 98 lacked support for many devices. Windows 98 Second Edition added some support.

Can you find a "Windows 98 Second Edition Upgrade" CD-ROM and
license-key?


Search for a wireless-adapter that *CLEARLY* states that it is supported on Windows 98 SE.

It's time to "trash" that computer.

Find somebody who has an older Pentium 3 or Pentium 4 computer that is running Windows XP, and buy that computer from them.

Contact any retail computer-store, or shop on eBay or AMAZON.
They can still sell you a "Windows XP Upgrade" kit,
to allow upgrades from Windows 98 (assuming that you still have your Windows 98 CD-ROM) to XP.

here ya go

http://www.officialdrivers.net/toshiba-drivers.php?gclid=CJip5OKvpJsCFQ4MDQodWCAtCg

Please post the missing devices Hardware ID.
What Service Pack level the XP is on? Currently Service Pack 3 is out for slipstreaming to create a bootable XP SP3 CD.

Here's What You Need to Use Windows XP Professional • PC with 300 megahertz or higher processor clock speed recommended; 233 MHz minimum required (single or dual processor system);* Intel Pentium/Celeron family, or AMD K6/Athlon/Duron family, or compatible processor recommended
• 128 megabytes (MB) of RAM or higher recommended (64 MB minimum supported; may limit performance and some features)
• 1.5 gigabytes (GB) of available hard disk space*
• Super VGA (800 x 600) or higher-resolution video adapter and monitor
• CD-ROM or DVD drive
• Keyboard and Microsoft Mouse or compatible pointing device

you may/will also need software drivers for all hardware eg: printer,sound card, video card...good to gather BEFORE you upgrade.
Soooo, if you have the required compnents and some free time and a little patience it can be done.
Just buy a xp pro cd if you haven't one already and git er done..

If you are using Windows 98, 98SE, ME, 2000, NT or XP, and have an ATAPI/IDE CD/DVD drive, there is no driver needed (see Toshiba statement I have posted below). Under no circumstances, if DVD is properly installed and functional, will you need ANY driver!

If your DVD drive is a SCSI drive, then it may need drivers specific to the SCSI card you have installed (see the specs/manual or website for your card). You may also need the Adaptec SCSI setup, available at this address:

http://www.adaptec.com/worldwide/support/suppbyproduct.jsp?sess=no&language=English+US&cat=%2FTechnology%2FSCSI+Software&fromPage=driverindex

or use this address if you have a LOGIC based SCSI card or device:

http://www.lsilogic.com/

Now, if you meet the criteria for the first paragraph I wrote, and your PC does not load the driver automatically (after a reboot or two) then you have a PHYSICAL or HARDWARE problem. Either the DVD drive is improperly cabled, improperly installed or defective.

Those are all your options. See below, from Toshiba website
good luck
-----------------------
http://sdd.toshiba.com/main.aspx?Path=ServicesSupport/DeviceDrivers

ATAPI CD-ROM and DVD Drivers

Toshiba's CD-ROM and DVD-ROM drives do not require any unique device drivers for Windows '95/'98/2000/XP/NT.
After installing your drive and re-booting, your system should recognize your CD-ROM or DVD-ROM. Win '95/'98/2000/XP/NT Operating Systems support all Toshiba ATAPI CD-ROM and DVD-ROM drives natively.

DOS/Windows 3.x Device Drivers

This device driver is to be used with DOS/Windows 3.x operating systems. Do not use this driver with Windows '95, Windows '98, XP or Windows 2000 unless you are going to use your system in the REAL or MS-DOS Modes. Device drivers for Windows '95, Windows '98, Windows 2000, XP, OS/2, and NT operating systems are provided with the installation or setup software of each operating system.

DOS ATAPI Interface Driver
If you prefer using DOS click the link below to download a MS-DOS ATAPI interface driver.
atapi.exe

SCSI CD-ROM and DVD Drivers

SCSI interface drivers are written for the SCSI card you are using in your system, by the SCSI card manufacturer. They are not specific to your Toshiba drive and are not provided by Toshiba. If during installation Windows can not find the correct SCSI software driver for your SCSI card and you do not have the software driver that came with your SCSI card, contact your SCSI host adapter manufacturer.

Adaptec SCSI Drivers
LSI Logic (Symbios) SCSI Drivers
DVD Viewing Software

Toshibas DVD drives require a third party software to be installed in your system to enable you to view DVD movies. If you purchased your drive as part of a kit, the software may have been included. The links below will provide some possible solutions should you not have this type of software.

Nero6 (Toshiba recommends)

Toshiba does not recommend nor endorse any of the following manufacturers software products. Software names are provided only as a courtesy to our customers. Please check with the software manufacturer to assure that their software supports your drive model.

DirectDVD
Cyberlink PowerDVD
WinDVD
Media Burning Software
Toshiba's recordable drives require third party software to be installed in your system to enable you to burn media. If you purchased your drive as part of a kit, the software may have been included. The link below will provide some possible solutions should you not have this type of software.

Nero6 (Toshiba recommends)

Toshiba does not recommend nor endorse any of the following manufactures software products. Software names are provided only as a courtesy to our customers. Please check with the software manufacturer to assure that their software supports your drive model.

NTI CD & DVD Maker
Gear DVD & CD-RW
Roxio Toast (Macintosh)
Easy CD Creator
Stomp Clinkn Burn Pro

By connecting the camera to a computer with the provided USB cable,
images on a card can be transferred to the computer. Some OS's (operating
systems) may need a special setup when connecting to the camera for the
first time. Follow the chart below. For details on the procedures in the chart,
refer to the “Reference Manual” on the CD-ROM and the “Software
Installation Guide” (included in the CD-ROM package).
Identifying the OS
Windows 98/98 SE
(Second Edition)
Windows 2000
Professional/Me/XP
Mac OS 9.0 - 9.1/OS X
*OS 8.6: See below.

Connecting the camera to a computer using the provided USB cable
Installing the USB
driver for Windows 98
Confirming the computer recognizes the camera
Downloading image files
Disconnecting the USB cable
 

Even if your computer has a USB connector, data transfer may not function correctly if
you are using one of the operating systems listed below or if you have an add-on USB
connector (extension card, etc.).
● Windows 95/NT 4.0
● Windows 98/98 SE upgrade from Windows 95
● Mac OS 8.6 or lower (except Mac OS 8.6 equipped with USB MASS Storage support
1.3.5 installed at the factory)
● Data transfer is not guaranteed on a home-built PC system or PCs with no factory
installed OS.
You can view images using: graphics applications that support the JPEG
file format (Paint Shop Pro, Photoshop, etc.); Internet browsers (Netscape
Communicator, Microsoft Internet Explorer, etc.); CAMEDIA Master
software; or other software. For details on using commercial graphics
applications, refer to their instruction manuals.