Raymarine A65 Combo GPS Chartplotter/Fishfinder Logo

Related Topics:

Question about Raymarine A65 Combo GPS Chartplotter/Fishfinder

1 Answer

The chart plotter worked perfect for 5 yeas,

My Raymarine chart plotter/GPS/Fishfinder worked perfect for 5 yeas, recently the screen say "No Chart Data". The first couple of times it did this I removed the Chart Card from one slot and placed it in the other card slot and it worked, now that does not work, help?

Posted by lliles on

Ad

1 Answer

Radoslav Segaric

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 43 Answers

I think you have a C- Map card (black colour)clean the contacts with a contactcleaner if it not works try the card somewhere else
The C-Map card have problems that they work for a while and than stops inside the card a some memorychips and they losing contact

Posted on Oct 22, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have problems with my plotter Raymarine Rc 435 chart plotter.This plotter can not location my ship to do.What is problems?

Be sure there isn't any aluminum in close proximity to your GPS antenna, or that your antenna is not to close to other powerful electronics. Aluminium reflects electromagnetic signals and other electronics emit EM fields as well causing disruption of your GPS signal reaching your antenna.
0helpful
1answer
0helpful
1answer

MY RAYMARINE A65 CHART PLOTTER/ FISHFINDER HAS NOT BEEN WORKING , THE CHARTPLOTTER WORKS FINE , BUT THE FISH FINDER WONT PULL UP BOTTOM OR ANYTHING . I LOOKED AT THE LITTLE BOX THAT CONNECTS TO THE...

Likely your DSM25 (that little box that connects the transducer to the display) will need to be rebuilt. The red LED is saying that there is an internal fault with the unit. You would need to send the unit in for repair through Raymarine (as there really is not anyone else who can do it), and they would have to replace the main circuit card in the box. I believe that they are charging either $150 or $175 to repair those now... but likely the only way you will get that one to work again.
6helpful
1answer

My Raymarine C80 CHart plotter won't load.

Check to see if this is a power issue by connecting to shore power and fully charging your batteries overnight with instruments off. While still connected to shore power, with batteries fully charged, turn on C80 navigation system. If the loading screen comes on and does not reset, then try holding down the button immediately to the right of the red power button for at least 3 seconds to see if the system re-boots.
0helpful
1answer

I have a Raymarine L755 chart plotter that is continuously rebooting. It shows the initial screen and holds it for about 5 seconds and then beeps, reboots and the cycle starts over. I have a L755...

Send it to Auckland back they can install witha C-MAp card a new
Software.
BUT it is verry important that you make after the instaltation a MASTERRESET.
If not you will have the same problem in a few month again
0helpful
2answers

I have a Raymarine L755 chart plotter that is continuously rebooting. It shows the initial screen and holds it for about 5 seconds and then beeps, reboots and the cycle starts over.

Make absolutely sure that all of the buttons are clear (not stuck). After that, begin by unplugging any external interfaces (including the chart card) one by one to determine if one of those is the culprit.
0helpful
1answer

RL70CRC crashes with new "Wide" C-map cartridge

get a new burn on the chip, I have seen this issue on a particular burn.
1helpful
2answers

Raymarine RL70CRC GPSRadar

Hi Matt,

There is a feature in these chartplotters called "Plotter Mode" that is often misunderstood and causes the exact problem you describe.

Press menu.....chart setup.....and scroll to the bottom until you see Plotter Mode in the list of options. It should be set in the OFF position.

If you have more than one display networked onboard check the setting in each one invividually.

What Plotter Mode does is allows the chartplotter system to access range scales not supported on the chart. It is not normally used for map-based navigation but more so for chartless electronic plotting (it can display routes, waypoints and track-recorder breadcrumbs.) open-ocean cruising, or for ultra-precise GPS operations (like a precision anchor drop, finding a very specific location etc. When plotter mode is on you can zoom in to a very, very small working area. The indicator it is enable is the cross-hatch background on the screen, the lack of map information, and the NO CHART DATA watermark on the screen.
Not finding what you are looking for?

416 views

Ask a Question

Usually answered in minutes!

Top Raymarine GPS Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Mike

Level 3 Expert

4383 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

55691 Answers

Are you a Raymarine GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...