Where can I get a vepv0037a display board

1 Answer

John Wardlow

Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

Habit-Forming:

Visited the website for 3 consecutive days.

Governor:

An expert whose answer got voted for 20 times.
Contributor
27 Answers

It may not be needed. Try shorting across this fuse protector IP1280 (looks like a resistor) on the power board. See more detailed solution I posted in this forum for a similar question. where can I get a vepv0037a display board - 4a63623.jpg

Posted on Jun 06, 2010

Tim J Apr 19, 2014

Thansk! My display had been dead for years and I was using the unit anyway but finally went to see in any display boards were available and ran across this. It fixed the problem immediately. Funny thing is a new display board wouldn't have helped! Wish I'd seen this years ago.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1helpful

1answer

I have a Sony HT-DDW660. Is the display inverter board easy to replace with simple tools or does it require professional installation? Finally, is this part still available and doesn't cost a lot?

the problem has to be from the display inverter board. The display inverter board is responsible from bringing display on the screen. Now since is no longer display, then it mean it has become defective.Get a philips screw driver, disassemble the unit in order to get to the display screen. You will see a kind of flex or wire connected to the screen. The board where the wire/flex is coming from into the screen is the display inverter board. The board is rectangular in shape.Remove the board, take it to an electronics parts store within your vicinity for exact replacement and the unit should display again.

Read full answer

Aug 23, 2020 • Sony Computers & Internet

0helpful

1answer

WMG30GS Whirlpool microwave display

please follow this steps and fix it. God bless you

Main control board If the display on your microwave has gone out completely this is usually a sign that it is a malfunctioned main control board. To correct the issue the main control board would need to be replaced.
Display board A display board can either malfunction completely or partially, causing two separate results. If the display on the unit has completely gone out, this can be attributed to either a bad main control board or display board. On the other hand, if the display has only partially gone out, this is usually a sign that the display board is defective and will need to be replaced

Read full answer

Nov 27, 2013 • Microwave Ovens

0helpful

1answer

What is a display board?

"Display board is a generic term for a board-shaped material that is rigid and strong enough to stand on its own, and generally used paper or other materials affixed to it. Display board may also be referred to as poster board or posterboard." (Wikipedia)

Read full answer

Oct 07, 2013 • Office Equipment & Supplies

0helpful

1answer

Are there electronic display boards?

Yes. Actually most of the display boards you see today, mainly in big cities are electronic display boards: http://www.szabsen.com/commercial-led-project.html?gclid=CIXqiJXigLUCFYVb3god3FsAYg

Read full answer

Jan 24, 2013 • Office Equipment & Supplies

0helpful

1answer

I have no power to the display (thus the machine will not run) but the fan will run. What do I do?

1) if your display use batteries ,replace by new ones.2)tight the flexible cord from keypanel vs display board3)tight the display board vs lower board( main motor board)4)see if your have 5VDC to display board coming from lower board.5) Test the lower board is coming the power 115 VCA + 5vdc COMING from power supply (transformer+ diodes+capacitor).6) Display board is faulty or Main Board(Lower board). Of course after you did check the step before. See the block diagram that I did for your illustration.

Sincerely. Good luck, G-d bless you.
ERNESTO CUADRAMANAGUA,NICARAGUA. C.A

Read full answer

Jul 17, 2011 • NordicTrack Treadmill

0helpful

1answer

Display board does not display any thing. The light/display board is on but the written message on the board does not display.

open the key board and replace 20 pin ic( no SN 74 LS 244) on lcd driver board.

Read full answer

Jan 03, 2011 • Canon imageRUNNER 400S Copier

0helpful

1answer

ANY IDEA WHERE I CAN GET A VEPV0037A PART FOR MY PANASONIC SYSTEM

May be the grid power to the display. Try shorting across this fuse protector IP1280 (looks like a resistor) on the power board. See more detailed solution I posted in this forum for a similar question.

Read full answer

Nov 02, 2009 • Panasonic SC-HT830V System

3helpful

2answers

No temperature display on my GE Profile PFS22SIS

I think is just the display board next to the cold control.

Read full answer

Oct 01, 2009 • GE Profile CustomStyle PSC23MGSWW 36" 22.7...

0helpful

1answer

VEPV0037A display board

Try this. Try shorting across this fuse protector IP1280 (looks like a resistor) on the power board. See more detailed solution I posted in this forum for a similar question.

Read full answer

Jun 27, 2008 • Panasonic SC-HT830V System

34helpful

13answers

The display on the front of the dvd player is not working

I finally got some time to run this one down. I first took the "easy" solution and just ordered a new display and replaced it. No luck.

I traced the problem to the grid voltage going to the fluorescent display, it is a vacuum tube and requires grid heater voltage. The circuit goes through a switching transistor on the display board (board not available) through the DVD board (circuit wiring only) through a diode and fuse protector on the power board (also not available) to a transformer. The fuse protector was open, but the transformer was not putting out the right voltage. I replaced the transformer and jumpered the fuse protector and that solved the problem. I will need to put something in there for circuit protection as it may be a current limiting fuse protector but the part was not even in the parts.com parts list.

Cause: Temperature and/or voltage surge caused transformer and fuse protector to fail. Transformer rang OK, only display voltage affected.
My Solution: Replace transformer T1150 and Fuse Protector IP1280.

Possible cause of others who replaced the display board: Voltage surge may have taken out switching transistor Q7001 on display board. This transistor is turned on by QR7201 & QR7201 in a Darlington pair when PowerSave goes low. I did not under stand this function since the display is never completely off. It may dim it but I don't recall the display dimming. It may be non function on this model so jumpering E-C on Q7001 might solve the problem for others.

Parts replaced:
T1150 Transformer G4D2A0000216
IP1280 Fuse Protector K5G252AA0003

John

Read full answer

Oct 02, 2006 • Panasonic SC-HT830V System