Alpine cde 9846

Yes. You can connect iPhone to Alpine CDE-9846 with help the cable: https://yadi.sk/i/otMTAdpsqyzyr

A thumbs up would be greatly appreciated if this answer is helpful to you. I suggest that you purchase a wire adapter for your vehicle so as not to cut factory wiring.

1. In the Clock priority mode, press and holdTITLE for at least 2 seconds while the time is displayed.The time indication will blink.
2. Turn the Rotary encoder CDE-9846 only) or press "up" and "down" (CDE-9842 only) to adjust the hours while the time indication is blinking.
3. When the hour has been adjusted, press the Rotary encoder (CDE-9846 only) or press MODE (CDE-9842 only).
4. Turn the Rotary encoder (CDE-9846 only) or press "up" and "down" (CDE-9842 only) to adjust the minutes while the time indication is blinking.
5. The time is automatically set 5 seconds after the minute adjustment.
6. The time can also be manually set by pressing the Rotary encoder (CDE-9846 only) or press MODE (CDE-9842 only).

Download Alpine CDE 9842 Manual

Setting Time

1 In the Clock priority mode, press and hold

TITLE/ for at least 2 seconds while the time is

displayed.

The time indication will blink.

2 Turn the Rotary encoder (CDE-9846 only) or

press 4 and 3 (CDE-9842 only) to adjust the

hours while the time indication is blinking.

3 When the hour has been adjusted, press the

Rotary encoder (CDE-9846 only) or press MODE

(CDE-9842 only).

4 Turn the Rotary encoder (CDE-9846 only) or

press 4 and 3 (CDE-9842 only) to adjust the

minutes while the time indication is blinking.

The time is automatically set 5 seconds after the minute

adjustment. The time can also be manually set by

pressing the Rotary encoder (CDE-9846 only) or press

MODE (CDE-9842 only).

• To synchronize the clock to another clock/watch or radio time

announcement, press and hold the Rotary encoder (CDE-9846

only) or press and hold MODE (CDE-9842 only) for at least 2

seconds after setting the "hour." Minutes will reset to 00. If the

display shows over "30" minutes when you do this, the time will
advance one hour.

http://www.alpine-electronics.co.uk/fileadmin/user_upload/manuals/car_audio_manuals/CDE-9880R/OM_CDE-9880R_EN.pdf

On page 20.

simple google alpine audio.com look for support the first thing is manules its strat forward or go to google and google http://valt.alpine-usa.com and its om_cde-9846.pdf

just run a kill switch to the radio

Pasted from the manual:
1 In the Clock priority mode, press and hold
TITLE/ for at least 2 seconds while the time is
displayed.
The time indication will blink.
2 Turn the Rotary encoder (CDE-9846 only) or
press up or down arrow (CDE-9842 only) to adjust the
hours while the time indication is blinking.
3 When the hour has been adjusted, press the
Rotary encoder (CDE-9846 only) or press MODE
(CDE-9842 only).
4 Turn the Rotary encoder (CDE-9846 only) or
press up or down arrow (CDE-9842 only) to adjust the
minutes while the time indication is blinking.
The time is automatically set 5 seconds after the minute
adjustment. The time can also be manually set by
pressing the Rotary encoder (CDE-9846 only) or press
MODE (CDE-9842 only).

I think you are using an external amplifier,if this is the case,you may be using the wrong remote wire for the amp.
Alpine use two blue wires,BLUE (only) this wire is for the pwr antenna and every time you insert a cd, this pwr line cut out.
BLUE/WHITE STRIPE this is the remote wire that you need to connect the remote of the amplifier.

thanks for rating

It's probably a solder in lamp. They can tend to be very tiny. About the size of the head of a paper match or smaller. If you're not good with soldering then I would suggest you go to a repair shop and let them do it. Good luck.