Dishwashers Logo

Related Topics:

Question about Bosch Dishwashers

1 Answer

Where can get a replacements clic assembly for my Bosch 1587vs

Posted by Steve on

1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    Visited the website for 3 consecutive days.

  • Expert
  • 103 Answers

You can find a replacement clic assembly for your Bosch 1587vs jigsaw online from Bosch or from third-party retailers. You can also find clic assemblies from hardware stores, home improvement stores, or tool supply stores in your local area. Make sure you get the correct clic assembly for your Bosch jigsaw model.

Posted on Feb 04, 2023

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


Bosch 1587vs blade won't tighten when installing

It sounds like you are having difficulty tightening the blade on your Bosch 1587vs jigsaw. To resolve this issue, first unplug the tool and lift up on the knob and loosen the spindle lock. Then insert the blade and push up slightly while doing so and twist to align the blade with the roller. Make sure to turn past resistance until it clicks. If the issue persists, you may need to replace the "clic" assembly, part #2-602-025-901.
Dec 12, 2022 • Bosch Saws

I have a bosch nexxt 500 series washer. When closed it clicks 3 times in series for 3 cycles and then displays e 01. I replaced the lock mechanism with a part directly from bosch and still the same

An answer found on a BOSCH support site said:

"the E:01 indicates a door lock error, make sure the door is closing tightly, you also may have a loose connection on either the door latch assembly or the control board, if these check out replace the latch assembly."

Since you've already replaced the mechanism then it seems possible a loose -connection- may be your problem. If you've already checked all this, please post back.

05'deville just clic clic when tryn to start it

Hi Allen, Make sure that the battery terminals are clean or better still replace them. check the connections on the battery and on the starter motor. If everything seems good the problem may well be with the starter solenoid and the contactors inside the unit. Regards John

How do I change a blade with the Bosch 1587VS?

you need to lift up on the knob to loosen the spindle and remove/install the blade. To install the blade you might need to turn it some and push up and when it is straight then you need to turn the knob while holding up on it till it is snug and then push the knob down.

How the h... do i cabnge the blade on the bosch 1582 cutter ??

I am assuming you are asking because you have a CLIC system.

Bosch uses a tool-less blade changing system for its jigsaws that it calls "Clic." The system makes changing blades fast and simple. With the simple blade changing you get with the Bosch jigsaws, it is no problem to change out a dull blade.


Make sure the saw is unplugged or the battery is removed.

If you have a blade in there:

Hold the saw over a work bench and push the ejector lever to the center of the front of the saw. There is a center stop; you will feel it. The blade will eject and fall out

Insert the new saw blade into the plunger until it latches into place. The teeth should face toward the front of the saw. The back of the blade should rest in the groove of the guide roller. The plunger and the guide roller are between the body of the saw and the plate

If the blade will not go into the plunger, check the positioning of the slots in the blade. They should be at the top. Push the ejector lever and try again.

Give the blade a yank to check that it is firmly seated. Plug the saw back in or replace the battery and proceed with the cut

Use protective gloves when handling blades. They can be sharp and can be HOT.

I hope this helps

Please rate FIXYA


May 20, 2011 • Garden

I need the schematics for my bosch jig saw (1587VS)

I have a blue wire that came of itscomes from the triger and goes to the motor can't find out where it goes need help
May 19, 2010 • Bosch Saws

After changing the blade on a bosch 1587VS jig saw the blade turns sideways when sawing. How is this corrected? Thanks

I would recheck the installation of the blade and the tightness. If still a problem there is a spring under the lever that might have broke (they tend to do that) and is jamming the spindle. Let me know and I will help you with the breakdown for this tool
Jul 26, 2009 • Bosch Saws
Not finding what you are looking for?

Open Questions:


Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts


Level 3 Expert

2511 Answers

mark warfield
mark warfield

Level 3 Expert

453 Answers


Level 2 Expert

225 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides