Xerox 7225 Blocked Interrupt Button keep Flashing

If your Xerox 3655i printer is experiencing issues such as a white display and a flashing interrupt button, here are some troubleshooting steps you can try:

1. Power cycle the printer: Turn off the printer, unplug it from the power source, wait for a few minutes, and then plug it back in. Powering it on again might help resolve temporary issues.
2. Check the display connection: Ensure that the display is securely connected to the printer. If there are any loose cables or connections, reseat them properly.
3. Perform a firmware update: Visit the Xerox support website and check if there are any available firmware updates for your printer model. If updates are available, follow the instructions provided by Xerox to update the firmware.
4. Reset the printer: Locate the reset button or option on your printer. It is usually a small hole that can be pressed using a paperclip or a similar tool. Press and hold the reset button for a few seconds to perform a reset. Note that this might reset some settings to their default values, so be prepared to reconfigure them.
5. Contact Xerox support: If the above steps do not resolve the issue, it is recommended to contact Xerox customer support or visit their support website. They will have access to specific troubleshooting steps and can provide further assistance based on the symptoms you described.

Remember to provide them with detailed information about the issue, such as the model number, the exact error message (if any), and any steps you have already taken to troubleshoot the problem. This will help them diagnose the issue more effectively and provide you with the appropriate solution.
Please note that printer repairs may require technical expertise, and it is advisable to consult professionals if you are not familiar with the internal workings of the printer or if the printer is under warranty.

Try this link:

http://wss.support.xerox.com/GTConnect/UnifiedAcceptor/AddWebFramework.Main/site/XeroxProductSupport/product/product_wc7220_wc7225/lang/en-US/region/region_US/source/DND/Xlang/en_US/Xcntry/USA/prodID/WC7220_WC7225/KBlang/en/t/1513871099278/#!view-content/ViewContent/View/contentId/x_wc7120_en-O14797

That is a black drum atc failure. First try to replace the black image drum and if that doesn't resolve it can be the MCU Board.

Your best bet is to go to the Xerox.com website and follow the troubleshooting guide.
Good luck.

Try this: 1. Turn machine off 2. After it has completely powered down, unplug the power cord from the wall. 3. Go back to the front of the machine and turn it on and then back off again (remembering to leave it UNPLUGGED from power.) 4. WAIT 60 SECONDS (Very important) 5. AFTER 60 seconds plug it back into the wall and turn it back on.
If problem persists call for service.
Hope it helps!

The default password is "00000" If this password does not work you can follow the following to reset it:

1. Power OFF the machine using the power switch located on the right side of the machine, toward the back. Press the power switch to the (O) position.
   
   
2. Press and hold the [OK] button on the Control Panel.
3. Continue to hold the [OK] button and power ON the machine. Keep the [OK] button held down until the Ready screen is displayed. The password is now reset to the default Control Panel password, which is 00000.
   
   NOTE: There will be no confirmation message during or after the machine's power on sequence. However, if the procedure was performed correctly, the password has been reset.

canon ir3300 error code E000019-0000, hOW CAN I SOLVE IT ???
NO KEY IS FUNCTIONING NOW.................
mail at [email protected]

H4-00 on Sharp means that the temperature inside the printer is too low. That is usually the fuser lamp, and sometimes the temp sensor jammed.

Only when the problem is a jammed temp sensor or a jammed control board you can reset the machine by doing a reset.

You try reset from simulation mode by following procedure below:
Clear key >>Interrupt key >> "0" key >> Interrupt key >> Main code >>Start key >> Sub code >> Start key

If the error remains, that means that the fuser is really bad and must be replaced.

When this happen you need to have the fuser unit replaced, if that does not fix the problem the technician will replace the temperature sensor.

Hi

If you find the lights flashing, we could try resetting the printer.I have explained the reset procedures below

POWER DRAIN:-Turn off the printer, Unplug the power cable from printer and from the wall outlet.Press and hold ON buton for 30-60 seconds.


PARTIAL RESET:-Unplug the printer power cable while its ON, press and hold # and 3 button and connect the Power cord while holding.Wait untill the ON light flashes, then release the buttons.

----(for below reset cartridges must be removed out)---------

SEMI_FULL RESET:-Remove the ink cartridges, Unplug the printer power cable while its ON, press and hold # and 6 button and connect the Power cord while holding.Wait untill the ON light flashes,or wait for 20 seconds,hen release the button.If the printer goes off dont worry release the button and Push the ON button.


FULL NVM RESET:-Take the Ink Cartridges out, Unplug the printer power cable while its ON, press and hold OK and CANCEL button and connect the Power cord while holding the buttons.keep Holding the buttons until the printer goes off ,release the button and Push the ON button.

Thanks
Riz