Samsung Dishwasher '0C' error during wash cycle.

Hi Ray.
i found this out.
The reason for the dishwasher to stop mid cycle is that the thermal fuse is shorting out because it is either fouled, dirty, broken, or loosely connected. If your dishwasher is older, the thermal fuse is used as a safety switch to stop the motor and circuit board when the dishwasher gets too hot.

or go to this link might help you out.
https://fixappliances.ca/dishwasher-repair/why-your-dishwasher-starts-and-stops-during-wash-cycle-and-how-to-fix-it/#:~:text=The%20reason%20for%20the%20dishwasher,the%20dishwasher%20gets%20too%20hot.

is there any error codes showing

most likely the water valves are stuck

Hi Roger, Hope this helps......CHEERS..

KENMORE DISHWASHER ERROR CODES

Kenmore Dishwasher Error Code = Start Resume light blinking slow
When the dishwasher door opens or electrical power is removed during the cycle then the dishwasher will not start again. The door is detected as being closed and the Start Resume button is being pressed
Kenmore Dishwasher Error Code = Clean light is blinking 7 times
Heater circuit fail. Control panel did not detect the water getting hot. Did not detect heating element was energized to heat the water during the wash cycle
Kenmore Dishwasher Error Code = Sanitize LED blinking at end of cycle
Control panel could not detect if sanitation has been achieved
Kenmore Dishwasher Error Code = Console light blinking rapidly
There is a stuck button on the control panel
Kenmore Dishwasher Error Code = Clean light is constantly illuminated
Dishwasher cannot start a wash cycle until it sees that the door has been opened after the previous washing cycle
Kenmore Dishwasher Error Code = Control lock LED is ON but not responding to pressing of the keys
Turned on by accident or there is a control detected key pad problem

The 5E error code on this Samsung dishwasher means a drain error. Most often this is caused by a clogged drain hose, or some foreign object getting caught in the drain pump impeller. But it can also mean you have a bad ECS sensor. If this is Greek to you, then you should probably call a professional dishwasher repairman.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

What 2 cycle lights? Samsung dishwashers indicate problems and errors by making different lights light up and/or flash. We would need to know the model number too.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

The statement below can be found at: http://www.ehow.com/list_6978265_bosch-dishwasher-error-codes.html,

The SHU4326 and 4326 models use "Regular Wash" and "Rinse Hold" to begin the test while the other three series in this section use "Scrub Wash" and "Delicate/Econo," but all use the same set of fault codes, shown not as lights but as numbers on the Cycle Countdown display. Here, 1 is an aqua sensor fault, 2 is a heating fault, 4 is a filling fault, 8 is an NTC fault and 0 means that everything is working as it ought. During an actual wash, when you aren't testing, the Cycle Countdown display may show the letter "F," which also signifies a filling fault.

Read more: http://www.ehow.com/list_6978265_bosch-dishwasher-error-codes.html#ixzz33JutQVQR

There is a nice repair guide with videos that provides troubleshooting steps and instructions for your dishwasher here:

Samsung Dishwasher Making Noise

Most likely a pump fault if no external water leak.

thats what it soundslike to me here aoart number which is the entire assy w/both switches included 99002254 retails for about $25