Are control boards plug and play?

Good morning, dissapointed81. I understand that you are experiencing some concerns with your dryer. Before contacting a service provider, I would suggest that you either unplug or turn the circuit breaker off to the unit for five to ten minutes. Let the dryer reset completely and try to use it as normal again. If this does not prove to be effective, we do recommend that a professional technician diagnose the thermal limiter and control board. The E66 error code typically indicates an error within the thermal limiter and interrupted communication to the control board. Though a full repair, and replacement parts, might not be needed we do recommend having a professional test the unit for safety reasons. -Hope this helps!

The EH0 error indicates a problem with the incoming voltage or the power supply or wiring inside the dryer. If there has been a problem with the electricity coming into your home (brown out or similar), the error will resolve when the power company fixes the issue. Otherwise the control board is not receiving the expected power from the power supply.

First unplug the dryer or shut off the power at the circuit breaker. Unplugging the dryer for at least 30 seconds will reset the error message. If you can, plug another appliance into the outlet and check if that works. If there is a wiring fault, get an electrician to check the outlet and wiring.

If the problem is inside the dryer, the power supply, the control board and the wiring to the control board will need to be checked. There could be a loose wire, a broken wire or a spot where the insulation has been damaged and two wires are touching. Check all of the wiring harnesses where groups of wires plug into the control board. Replace or fix any damaged parts or wires. The parts diagrams are available here: https://www.ransomspares.co.uk/parts/brands/electrolux/tumble-dryers/edc2086glw%20(91609724100)/ . If the dryer is under warranty, contact Electrolux to have the unit serviced.

I hope this helps.

Cindy Wells

I replaced the temperature sensor and the F03 Error persists. Looking through the manual I find no ref to a thermal fuse, so I am assuming my my model does not have one. Also I installed a brand new Power Control Board and still have the F03 error. The issue started when I fitted the Control Unit, sets temperature and timer for lower oven.

I have fixed a lot of these Dryers with that same problem.
The control board needs three relays to be replaced.
You need to get the same type relays.

The F14 error indicates a problem between the touch pad and the display control board. This could be a wiring problem so check the wiring harness between the two parts. Make sure that the wires are properly seated and check for corrosion at the connectors. It could also indicate that either the touch pad or the display control board (or both) are faulty. If your wiring is good, you need to replace the touch pad. If the error persists after replacing the touch pad, you have to replace the display control board as well.

The parts are available here: http://www.searspartsdirect.com/model-number/ew30gs65gs1/1412/0124250.html . See parts 19 and 20 on the control panel diagram.

I hope this helps.

Cindy Wells

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Hello Elizabeth P Cochran - Try resetting the unit by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and restart unit. If the door does not open, then it sounds like the washer is possibly experiencing a communication problem with the control board, wiring failure or faulty door lock. Contact a professional to move forward accurately to properly diagnose/repair unit.

Hello,
I am not sure what your Dryer model is or its age but it could well be that there is a plug loose on the main control board or some fault on the wiring inside the top behind the display panel.You could check to see if this is the case but make sure the mains power is off first,remove the top lid and check,or It would be best to get in touch with Electrolux to see if a repair is covered under the Warranty.
Hope this helps.

Good luck.

HI. Generally, this will be the result of a communication error. There is, possibly, a bad connection at the control panel board. This connection may be worn,or simply disconnected, slightly. Gain access to the back side of the control board, and check to make sure of proper connections at the control board. If you notice a slight separation of any connector, simply reconnect it, tightly. If there are not separated connections at the control board, replace the control board, entirely.

OK, your control board and LED are integrated, so you will need to just replace the control board. I would try a hard reset before replacing the board. Pull the plug or, shut down the appropriate breaker switch for 5 minutes. Re apply power after the 5 minutes are up. if you continue to experience this fault, replace the control board asap.

CONTROL PANEL(CLICK HERE TO ORDER)