Samsung Tv model: UN60F7100AF. No remote, plugged it in and red light at button right of tv but no picture. No buttons on tv, not sure if i just cant turn it on or if the picture is fried.

Check the power supply.

The Hitachi LE49S508 red LED lights up when the TV is in standby mode. The LED will be off when the TV is on or has no power. If you haven't tried the front panel buttons, check if the TV will turn on when you press the lowest button (Power) on right side of the TV. If this works and your remote doesn't, you may have a problem with the remote or the IR receiver. (You can check the remote by having someone take a picture of the front of the remote when you press a button. There should be a flare of light visible in the picture.) If your current source is a PC, make sure that the computer is on and hasn't gone to sleep. Otherwise, the TV main board is not getting power from the power supply or not responding correctly to the commands.

Sears Parts Direct has the owner's manual for the LE49S508 here: https://www.searspartsdirect.com/partsdirect/user-manuals/le49s508-hitachi-parts-manual . To download the manual, the current link is https://c.searspartsdirect.com/mmh/pd_download/lis_pdf/OWNM/1412002L.pdf . A few parts for this TV are available here: https://encompass.com/model/HITLE49S508 .

I hope this helps.

Cindy Wells

Normally on the Panasonic tv this will call for a service call. The key to getting it repaired correctly is to check for a certified Samsung repair shop because most of the parts come from Samsung. Now if you want to do your own research call to 800 number for Panasonic Tv see if there are any problems with that model that the manufacturer has extended but does not post. I had one repaired that the red light on also so I understand and it went out approximately 4 3/4 years. If your in the Atlanta area use Norman electronics they have repaired hundreds on tvs for me due to my work.

tv seems to turn on but no picture? - Forums - CNET

www.cnet.com > Forums > Samsung

CNETJun 11, 2015 - ... Samsung Dlp TV (HLR-5067W) it seems like the TV turns on butthere is no picture. ... the lamp is, light is visible from where the lamp is located but no picture. DLP Twon't turn on, blinking green lamp light then shuts dow ...
Jun 11, 2015
Samsung Plasma TV - Won't turn on
Jun 11, 2015
The timer, lamp, and standby/temp. light are flashing?!
Jun 11, 2015
Samsung TV Keeps Shutting Down
Jun 11, 2015
More results from www.cnet.com

TV with Black Blank Screen Repair How to Troubleshoot ...

? 3:16
https://www.youtube.com/watch?v=kFdVi2ejfzA
May 8, 2014 - Uploaded by ShopJimmy.com
TV Repair Help for a TV With a Black No Image on the Screen ...I Have A Sanyo TV I Can Hear But Black Screen Im 14 And Dont Know What To Do ! .... power button the power light goes from red to green, the screen flashes on then goes black ....Troubleshooting LCD Backlight Failure Samsung LNT-4066 ...

Samsung plasma tv repair blinking light no picture ...

probably you have defect mainboard .

Hello
Sky remote codes for Samsung TV are:

065 584 615 037 245 476 516 292 318 236 398 244 100 118 060 088

646

672

642

Follow the steps below

1. Select any channel on the TV.

2. Point your Sky+ remote control away from the TV and press the tv button.

3. Press and hold down the Select and red buttons simultaneously on the Sky+ remote control until the red light at the top of the Sky+ remote control flashes twice.

4. Input the 3 digit number from the Sky+ remote control codes then press the Select button. The red light at the top of the Sky+ remote control should flash twice.

5. Point the Sky+ remote control at the TV and try the volume button.

If this works try the other TV functions.

If these work then the correct code has been selected.

It's important to note that not all TV functions will be supported by the Sky+ remote control e.g. Picture in Picture.
?

If all functions do not work correctly, then repeat steps 1 - 3 and work through all the relevant 3 digit numbers from the Sky+ remote control codes, until you find the code which supports all or as many of the TV functions as possible.
Please note: In order to operate both your TV and Sky+ with your Sky+ remote control, you will be required to switch modes e.g. to switch on your TV from stand-by, you would need to press "TV" followed by the "Stand-by" button. Then to change channel on your Sky+ you would need to press the "Sky" button followed by the "TV guide" button.
OK.

Step 1: Remove the batteries

Step 2: Press the power button (red button) on the remote control 5 times.

Step 3: Replace the batteries and your remote should work fine.

1. Press tv on your Sky remote control.

2. Press and hold down select and the red button together until the red light at the top of your Sky remote control flashes twice.

3. Press tv again

Then enter the remote control code using the number keypad. The red light will flash twice if a valid code has been entered.

Samsung Code: 0060

4. Point your Sky remote control at your TV and press the Power button. If this turns the off as you'd expect, then the tv should be set, press Select and the remote should work

5. If the TV does not turn off press tv, then press the Power button again, repeat this process until the TV turns off, when the TV turns off press Select.

same as ak_medic