My Sherwood 525 receiver only displays the fm input option when rotating the input knob

Receiver OUT to Equalizer IN and off to the speakers.

Or look up

make model manual

on both of them.

https://www.google.com/search?q=sherwood+receiver+manual

Sherwood RX-4109 Operating Instructions Manual

ManualsLib https://www.manualslib.com > ... > RX-4109

View and Download Sherwood RX-4109 operating instructions manual online. Am/Fm Stereo Receiver. RX-4109 stereo receiver pdf manual download.

Sherwood RX-4109 user manual (English - 18 pages)

Manuals.ca https://www.manuals.ca > receivers > Sherwood

User manual. View the manual for the Sherwood RX-4109 here, for free. This manual comes under the category receivers and has been rated by 3 people with an ...

..

O.k. what inputs do you have at the rear? Send me a pic would be better

You need a cable to from TV sound output to your sherwood TV input.

Unfortunately the RX-4105 is a stereo only receiver with only analog L/R inputs. You will have to find a stereo output & go in through one of the stereo inputs.

Do you happen to have the replacement lamp for my Sherwood stereo receivers fm indicator

Go to...

http://www.sherwoodusa.com/service/index.php

Input your zip code, and within miles.

Press and hold 'SEL' press down arrow until CLOCK H is displayed rotate Volume knob to adjust press down arrow once to display CLOCK M rotate Volume knob to adjust press 'SEL' to finish. Reference pages 6 and 10 in this link to your JVC KD-G120 Instructions Manual.
http://resources.jvc.com/Resources/00/00/91/GET0330-001A.pdf

Check your antenna connections. Make sure your FM antenna is hooked up to the FM antenna terminal or jack on your Sherwood receiver. If you have the antenna hooked through the coaxial cable, check your coaxial cable with an ohmmeter for continuity. You can buy a volt-ohm meter as little as $12. Usually bad connection occur between coaxial cable and the the coax cable connectors. If that doesn't solve the problem, then there may be something wrong with your tuner card inside of your Sherwood receiver.

If you receivers display does not change channels or frequencies or AM or FM mode, when you try to change the channel or frequencies, or AM or FM mode, there may be something wrong with the front board of your receiver.

If there is something internally wrong your Sherwood receiver, you need to take it to a qualified technician that can fix it. Do not try to repair it yourself. If you don't know what you're doing, you can do far more damage to that Sherwood receiver to the point that would be very costly to repair.

Before you take your Sherwood receiver to a technician, try to unplug the receiver, and leave it unplugged for several minutes, and then plug it back in. If that doesn't solve the problem, then you need to take your Sherwood to a qualified technician.

Same thing happened on my R-925RDS. The memory backup capacitor in this case is C322 on the front panel PCB, over on the far left hand side by the mains power button.

In the case of the 925 it's a 0.047F 5.5V capacitor, a small black block approx. 10mm high with 10x5mm footprint. In the service manual it's referred to as 0.047uF, but this is incorrect. Replaced it with a 0.1F 5.5V memory back up capacitor, all's well.

If replacing the capacitor, BE CAREFUL where you mount it! Putting a standard (round) backup capacitor in the exact location of the old one may bring it very close to the mains switch. What I did instead was mount mine about 2 inches closer to the centre of the board, using double-sided tape, and ran wires back to its connection points.

If it is just a 2 pin "figure of 8" type plug(shaver plug) they are available most any electronics hobby shop, or an appliance retailer. If you have trouble identifying the socket on the amp... get back to me here. Good luck:)

regards
Graeme