Car Audio & Video Logo

Related Topics:

Question about Car Audio & Video

1 Answer

Which setting is for ohms own a micront22-184meter

Posted by Kirby on

Add Your Answer
Ad

1 Answer

Cindy Wells

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.

  • Car Audio & ... Master
  • 6,586 Answers

Do you mean a Micronta 22-184 multi-meter? The Ohms position is depicted by the Greek letter Omega. This is the third position from the right. The DC milliAmps setting is just to the right. See the picture here: https://www.ebay.com/p/12027907565. I had to do the counter-intuitive decrease font/image size to enlarge third picture from the end to see the characters in the image.

I hope this helps.

Cindy Wells

Posted on Jul 24, 2022

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
1answer

Impedance setting on Yamaha AV Receiver
Hi. You can always use a Receiver with an output impedance that is lower than the speakers input impedance.Problems arise when you try to use a Receiver with a higher output impedance than the Speakers input impedance.

Receiver 6 ohms speakers 8 ohms......YES..
Receiver 8 ohms Speakers 6 ohms.......YES, WITH CAUTION
Read full answer
Jan 15, 2013 • Yamaha RX-V673 7.2 Channel AV Receiver...
0helpful
1answer

Speaker impedance and the Yamaha RXV 463
You risk to crash a set of speakers. In any case this will have a detrimental effect on the sound
Read full answer
Aug 04, 2008 • Yamaha RX-V659 Receiver
3helpful
1answer

How to set GDT-311 Digital Multimeter to x 1000 ohm setting?
The 20K setting is close to what you're looking for. The 200 scale is best to read 0 to 200 ohms, the 2K setting would be to read 200 to 2K, the 20K is to read 2K to 20K, the 200k range is for 20K to 200K and finally, the 2000K is to read 200K to 2000K or (2M) ohm resistance.

Basically, start on the high range, and work your way down until there is only one (or none) digit after the decimal point in the display for the best accuracy. A 6,500 ohm value may display as .006 reading on the 2000K range, and as you can see, doesn't give a true reading of the actual value.

I hope this helps!
Read full answer
Apr 12, 2012 • Gardner Bender Measuring Tools & Sensors
0helpful
1answer

I Have A Peavey Valveking head and cab. I was wondering what inputs for the OHMS to put it on if i were to be playing in a band. 4, 8, or 16? and what input do i plug the speaker cable into on the cab, the...
The answer all depends on the impedance of your speaker(s). A single speaker can be plugged into either jack. Set the switch to the impedance of your speaker. If you use two speakers, set the switch to one half of the impedance of the lowest impedance speaker. Very few speakers are 16 ohm types. Most are 8 ohms and some are 4 ohms. You could plug an 8 ohm into each of the jacks and set the switch to 4 ohms for example.
Read full answer
May 28, 2011 • Peavey Valveking Head
0helpful
1answer

I have a budda superdrive 30 II amp and have a setting question. I made a 2-12 cabinet to hook to this amp. Each speaker is 4 ohms. They are wired to their own output jack. My amp has 2 outputs for...
You best rewire the cabinet to put the two speakers in series. Wire one speaker plus to minus of the other and bring the other lead, one from each speaker to your jack on the cabinet. The amp output impedance is what is set on the switch... for two 8 ohm speakers you would use both jacks to the two speakers BUT ssince you have 4 ohm speakers the ONLY option is for two in series and set the switch to 8 ohms. The amp is ONLY 30 Watts so don't expect too much sound output... You should get a nice CLEAN sound at a reasonable level. If you drive the amp too hard it will clip and you will get garbage.
Read full answer
Apr 22, 2011 • Budda Superdrive 30 Series II Amp Combo
0helpful
1answer

Why does the kenwood kac-9103d has two sets of terminals if its a one channel amp so how do i hook up a dual 12 phoniex gold 1200 watt sub to it
Hello damasogrizzl,

The 2 sets of terminals are connected internally. Having 2 sets just makes it more convenient when wiring multiple subs. The amp is rated for 900 watts RMS into a 2 ohm load. The specs claim that it is stable at 1 ohm but does not give a power rating.

The Radial SD competition series from Phoenix Gold are rated to handle up to 600 watts RMS. If you have the model RSdC124 with dual 4 ohm voice coils, it would be best to wire the voice coils in parallel for a 2 ohm load and connect the sub to one set of terminals on the amp. If your sub is the model RSdC122 with dual 2 ohm voice coils, you should wire the voice coils is series for a 4 ohm load and connect the sug to one set of terminals on the amp. Wiring the voice coils in parallel will result in a 1 ohm load. And, while the amp may be stable at 1 ohm, the sub will be seriously overpowered.

Hope this helps.
Read full answer
Sep 23, 2009 • Kenwood KAC-9103D Car Audio Amplifier
2helpful
2answers

Can I mix 6 and 8 ohm speakers?
I would not suggest mixing. Use either 6 or 8 only but i highly suggest not mixing unless it gives the option to set a certain input for a certain Ohm. If you mix your either going to mess up a speaker or the receiver itself.
Read full answer
Jun 01, 2009 • Yamaha RX-V463 Receiver
0helpful
2answers

Reciever turns off
Powering off usually points to issues with speaker setup. You should read pages 42 and 96 of the 606 manual.

Page 42 covers impedence settings. Check your impedence settings for your speakers. The 606 handles speakers from 4 to 16 ohms. There are two impedence settings on the 606 - 4 ohms and 6 ohms. Set to 4 ohms if your speakers are 4 ohms or more but less than 6 ohms. Set to 6 ohms if your speakers sit between 6 and 16 ohms. Incorrect settings can result in the 606 going into power protection after prolonged use or at higher volume.

Page 96 covers testing for unexpected power protection. You should switch off your AV at source and leave for an hour. Disconnect all cables to speakers and other peripherals (TV, DVD et al). After an hour turn on AV and turn volume to MAX, If the AV remains on, turn down volume to min, switch off AV and reconnect all devices. Make sure the speaker cables are properly connected and that no bare wiring is exposed.

Once you have done this switch on the AV and turn to volume to MAX. If the AV stays on then problem solved. If the AV switches off then you should contact your supplier.
Read full answer
Nov 24, 2008 • Onkyo TX-SR606 Receiver
0helpful
1answer

Plug wire
Did you buy the copper core (Low Ohms) or the carbon core (High ohms). The higher ohms will give you a higher voltage spark, assuming your coil can deliver it.
Read full answer
Nov 20, 2008 • 2007 BMW K 1200 GT
0helpful
1answer

Plug wire help
Did you buy the copper core (Low Ohms) or the carbon core (High ohms). The higher ohms will give you a higher voltage spark assuming your coil can deliver it.,
Read full answer
Nov 10, 2008 • 2004 ATK 500 Intimidator
Not finding what you are looking for?

View Most Popular

Car Audio & Video

Related Question

Impedance setting on Yamaha AV Receiver

  • Yamaha RX-V673 7.2 Channel AV Receiver BONUS PAK w/ Two HDMI Cables

Open Questions:

0answers

DUAL XDVD210 6.2" TOUCH SCREEN DVD CD USB SD CARD RADIO. Why is my touchscreen on my XDVD210 not working please?
Read full answer
Be the first to answer Dec 27, 2022 • Car Audio & Video
0answers

Schematic diagram for Orion hcca 275r
Read full answer
Be the first to answer Dec 16, 2022 • Orion Car Audio & Video
0answers

does anyone have schematic for audiotrak 500 amplifier?
Read full answer
Be the first to answer Nov 22, 2022 • Car Audio & Video
0answers

2012 elite eight mega motion scooter I have 4 wires broken underneath my scooter red .black .blue. green.
Read full answer
Be the first to answer Nov 01, 2022 • Car Audio & Video

36 views

Ask a Question

Usually answered in minutes!

Popular Questions

Pioneer AVH-P5000DVD stereo USB Error 23

Car Audio & Video

Honda CRV car radio

Car Audio & Video

Owner's manual needed for a Pioneer EEQ MOSFET 50WX4 Super Tuner III D

Car Audio & Video

Honda CRV Radio Code Error

Car Audio & Video

Why is it error-10 on my pioneer?

Pioneer AVH-X2500BT

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5048 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

The Knight
The Knight

Level 3 Expert

76851 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Crossfire-vr-Manual.pdf....

Crossfire VR600D Car...

PDF Manual
Swe-1390_om.pdf. user-manual-Used...

Alpine Used...

PDF Manual
OM_MRV-V500_EN.pdf. user-manual-2/1...

Alpine 2/1 Channel...

Loading...