Model WAT24160IN/01. Why does door lock symbol keep blinking?

Possibly the control board is failed.

This can happen so easily, my cat knocked a button, and the lock message came on and it seemed could not use washing machine. Easy fix though, look at bottom of program buttons, find the lock buttons (numbered 3 and 4 instruction manual)which have lock symbol (numbered 9)bracketed down the bottom, hold these two buttons(3 & 4) together for a few seconds. You will hear a beep, then see unlock appear in the door lock section. Fixed and ready to again wash.

It can be any of the car doors not got properly locked or the door is locked but the switch is not sensing the door locked. Open and close each door again properly.

Or else its problem with any of switch wiring getting in contact with alarm wiring causing it to happen.

And last thing alarm connections need to be inspected. It's getting short somewhere in between.

There are few help links with solutions, to troubleshoot these types of problems. I suggest going through these links.

Click the link below: ------

Volvo car alarm keeps going off for no reason

http://technoanswers.blogspot.in/2012/07/volvo-car-alarm-keeps-going-off-for-no.html

------------------

Alarm keeps going OFF

http://technoanswers.blogspot.in/2012/07/alarm-keeps-going-off.html

--------------

2009 Toyota Camry: Hood Switch causing Alarm to go OFF?

http://whatisbyme.blogspot.in/2012/04/2009-toyota-camry-hood-switch-causing.html

----------------

Ford Pickup Alarm will not disengage?

http://technoanswers.blogspot.com/2012/01/ford-pickup-alarm-will-not-disengage.html

------------

Mitsubishi Diamante: Factory Security Alarm will not go Off

http://www.howtorepairguide.com/2012/11/mitsubishi-diamante-factory-security.html

------------

Toyota Avalon Factory Alarm will go off?

http://repairhelpcenter.blogspot.com/2012/01/toyota-avalon-factory-alarm-will-go-off.html

----------

Chevrolet Tahoe Hood open warning on dash and alarm sounds?

http://schematicsdiagram.blogspot.com/2011/12/chevrolet-tahoe-hood-open-warning-on.html

-----------

These details will help.

Thanks.

Push the lock button - this should stop the blinking and allow the remotes to work properly

If by "main opener" you mean the wall control is blinking, press and hold the lock button for 3 seconds.

Press and hold the lock button for 3 seconds to stop the light from blinking. That blinking is the indication that the lock function is on and your remotes will not work.

I GOT SONY VAIO PCG-384L LAPTOP AND IT KEEP ON CRASHING,
I CANT FIGURE OUR WHAT IS THE PROBLEM?

hold down the menu button for 20 seconds until the lock symbol turns into an unlock symbol.

If the clean light flashes 7 times, pauses then repeats...

If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).

To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

If the issue returns, you could have a problem with the heating circuit (ie. element, thermostat or wiring). It rarely happens but it could also be the door switch not engaging properly when the door is closed (slightly bend the door latch down making sure it doesn't hit the door when you close it).

Hello,

I had the same frustrating dilemma with my Craftsman LiftMaster garage door and Keypad, Model 139.53754-01 (dated 10/06; and has the # 315 MHz).

To resolve “the dilemma”, grab your keypad, climb up on a ladder to access the garage door opener’s motor unit. On the right side of the motor unit, remove the white plastic casing by pressing buttons on each side and pulling down. This will expose the programming area, and for our purposes, the “Learn” button.

1. On the motor unit, press and release the “Learn” button. The Learn indicator light will glow steadily for 30 seconds.

2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button.

3. Release the ENTER button when the motor unit lights blink. The code has been “learned”/stored/activated.

Good Luck, and I Hope this Helps!
Gail
For possible future reference:

How to change an existing, known PIN
(Changing an existing PIN can be done with the wireless remote keypad, and does not require access of the motor unit.)

From the keypad:

1. Enter the four digits of the present PIN, then press and hold the # button. The opener light will blink twice. Release the # button.

2. Enter your new 4-digit PIN and press Enter. The motor unit lights will blink once when the PIN has been “learned”/stored/activated. Test by entering the new PIN, and pressing Enter.