How do you fix a wacky digital volume control?

The digital volume control section circuit has the fault. You have to check its main digital board. Might need replacement.

Get an Earphone or Headset which has a Volume Control On it! Control the Volume from there, Because we cannot Fix it!!!
Good Luck!!!!

Good day Mr.Daniel Navarro..

The picture below is the sample 42" plasma TV (internal parts)..

If your TV won't adjust volume or change channel by pressing button on the front panel..The problem could be the digital control board,it is the one that have a rectangular red on the image shown..

But before you replace the board make it sure that the control button assembly is properly connected on the said digital control board ( no loose connection or loose solder)..

Also try this remedy:
If you have remote control you can use it for the mean time to adjust the volume and channel so that you don't need to replace the digital control board..

Hope it helps..

Thanks for using fixya and purchased my service..Please don't forget to rate my answer..

Hi,
It sounds like the main control board has gone wacky....
replace the control/timer

. That is not that hard to fix and you can easily buy the parts yourself online...

Here is a tip that will help you with the online buying...

How to Buy Appliance Parts Online

heatman101

Turn on Ipod, on the left hand side there is a volume control switch. While you are on a song, hold the top of the volume control switch to increase the volume.
If that does not work then touch "settings", then touch "music" and make sure your "Volume Limit" is set to "Off", if it is not touch "Volume Limit" and set it to "Off".
Please do not forget to rate me

Based on your model camera, this might be a defective CCD imager. If so, Canon should fix this for you for free worldwide, and may also include free shipping both ways (free shipping varies with countries). This is regardless of your camera's warranty status. Please check this link for more info.

Applicable cameras include: A40, A60, A70, A75, A80, A85, A95, A300, A310, S1 IS, S60, S200, S230, S330, S400, S410, S500, SD100, SD110, IXUS V2/V3/300/400/430/500/II/IIs, IXY Digital 200a/300a/320/400/450/500/30/30a

Article ID: 932875 - Last Review: December 30, 2009 - Revision: 6.0 Resolve Hotkeys or Volume control keys not working on Microsoft keyboardshttp://support.microsoft.com/kb/932875

Worked for me Model 1031 Microsoft Digital Media Pro Keyboard
1-11-10

Your volume control switch in the cirucit is damaged - call Philips and find out if you are still in-warranty.

-Tha Mp3 Doctor

Hold down the "time set" button until the time on the clock flashes. Then use rev or fwd to set the time. Press the "time set" button again once you have the correct time. You can do the same to set the alarm by holding down the "alarm set" button.

Make sure you back up all songs on the GoGear before attempting this solution.

1) Back up all files on the GoGear
2) Open up Philips Device Manager (Start --> All Programs --> Philips)
3) Click on the Repair Tab, and look for a msg that says connect the player while holding the volume + button
4) Disconnect the GoGear from the computer and turn the GoGear off - hold in the volume + button and continue to hold it as you reconnect the GoGear to the computer; after holding the volume + button for up to 20 or 30 seconds, a window will open up saying that your device is being repaired (now you can let go of the volume + button); after the repair is successfully complete, your GoGear will be good as new

Now you can do the firmware upgrade that will prevent this problem from occuring in the future. Open up Philips Device Manager and click the Update tab. This problem was caused because most GoGear's were designed for Windows XP with Media Player 10 (which is no longer the latest standard).

-Tha Mp3 Doctor