Question about Samsung Office Equipment & Supplies

1 Answer

After Windows 10 update Samsung SCX 4828FN printer went from printing single side to double sided, how do I get it back to single?

Posted by JOHN on


1 Answer


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Samsung Master
  • 2,677 Answers

To print a duplex page, follow these steps:

  1. Go to Device and Printers. ...
  2. Right click on the printer, then select Printer Preferences. ...
  3. Below Double-Sided Printing select Long Edge or Short Edge depending on preference. ...
  4. Click Apply and OK to save the changes.

Posted on Mar 28, 2020


5 Related Answers


Shaira Enomar

  • 96 Answers

SOURCE: double side printing issue with HP 2420

Try to default on your page setup.

Posted on Jun 16, 2008



  • 1847 Answers

SOURCE: Paper Jam in Duplex mode when printing more than 1 sheet

check between the rollers there will be small bits of paper jammed in that is the reason.

Posted on Sep 09, 2008


  • 2 Answers

SOURCE: HP Color Laserjet 5550 not printing duplex

Hi, Check that the printer driver has duplex (double sided) turned on.

That's if u hav not already solved it :-)

Posted on Sep 17, 2008


  • 214 Answers

SOURCE: Printing everything double sided

go in youre ip address, log in as admin, chooce print tab and there is a print tab, there is a default options, and choose double printing off

Posted on Nov 12, 2008


Leroy Elliott

  • 2120 Answers

SOURCE: Double-sided printing on HP Laserjet 3330

Reinstall the driver..

Posted on Mar 05, 2009

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hello, I have problems with Duplex print at my SCX-4828FN since using a "new" refilled toner cartridge. I already exchanged this refilled one by an original Samsung MLT - D2092L/ELS (S/N C769B8WD4A02BHV),...

Hi, Your printer have problem with drive Clutch. To match grease. You have to dismantle the clutch and clean them. This is typical defect of SCX 4838, 4824. Cheers !!! :)

Sep 14, 2013 | Samsung SCX-4828FN All-In-One Laser...

1 Answer

Can't reset double sided printing to single side only as default

Exact same problem... took a couple of hours of fiddling but seems that to get it to stick you have to change the printer settings in windows rather than when you are actually printing a document. eg Control Panel > Printers > right click printer > Properties > (General tab) Printing Preferences > then for Double-Sided Printing select 'none' and press OK. Job done.

Oct 08, 2012 | Samsung SCX-3400 All-in-one Laser printer...

2 Answers

Samsung 4828fn wont print message - system error - cycle power

All SCX-4828 and SCX-4826 buyers should launch a class action lawsuit against Samsung. I have TWO identical SCX-4826 printers, purchased at the same time. BOTH developed "System Error, Cycle Power" errors within a few weeks of each other! I suspect this is a programmed "error", not that something is "worn out" but rather it is in the programming of this series of printers. In other words, I believe they are "designed" to break after a certain length of time (in my case, just over 2 years of use - how convenient for them, just out of an extended warranty). I called a Samsung repair shop and was told that it was a "Fuser" problem. How could 2 printers develop an identical problem within weeks of each other? Coincidence? I think not!

Jun 30, 2011 | Samsung SCX-4828FN All-In-One Laser...

3 Answers

Reset chip samsung 4828fn

If software reset software is not working then, you can use hardware module to reset printer permanently. [email protected]

Jan 18, 2010 | Samsung SCX-4828FN All-In-One Laser...

1 Answer

Idont have cd for installation

Driver, Manual, Or Software can be downloaded from this Link.

Jan 13, 2010 | Samsung SCX-4828FN All-In-One Laser...

2 Answers

Printer Error "Toner Exhausted". How i can clear this problem. i used Ssmsung SCX-4828FN Printer.

Reset Your Printer through Reset Software which works for next 5000 copies printed. You have to reset again and agian after every 5000 copies printed. visit for solution

Oct 05, 2009 | Samsung SCX-4828FN All-In-One Laser...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Cindy Wells

Level 3 Expert

6220 Answers

The Knight
The Knight

Level 3 Expert

76466 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides