Office Equipment & Supplies Logo

Related Topics:

Japhet Medali
Japhet Medali Posted on Jan 14, 2020
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

I removed an Eprom from the main board and returned it... To the suprise of machine not displaying anything and not warming up. The machine is Dsm 618 Nashuatec ..kindly help

Answer This Question

1 Answer

Harrie

Level 3:

An expert who has achieved level 3 by getting 1000 points
Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.

  • The Master 6,746 Answers
  • Posted on Jan 14, 2020
Harrie
The Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.

Joined: Jan 31, 2009
Answers
6746
Questions
0
Helped
1284508
Points
83153

Did you put it back exactly like it was before? Are you sure all connections sit ok?
Were you safe with E.S.D. (Electro Static Discharge).
Because handeling with bare hands could damage any electronic chip.
I'm afraid you need the help of an expert to solve your problem.

5 Related Answers

Anonymous

  • 37 Answers
  • Posted on Aug 14, 2008

SOURCE: REX ROTARY DSM618 D SC545 ERROR CODE

you have to go into the sp modes to clear this code .pres the yellow c then 107 and hold down the orange c , do this all in sequence , it wil go in the sp modes and show copy sp .enter there and switch the power off wait 5 seconds switch back on

Ad
Silverdragon

electronic & computer repair& servicre

  • 12061 Answers
  • Posted on Mar 09, 2010

SOURCE: my toshiba tecra8000 laptop displays toshiba logo

The BIOS password is removed by the BIOS configuration, you need the BIOS password to get into the BIOS configuration.But if you do not have the BIOS password then you need to construct this dongle device.
TOSHIBA BIOS PASSWORD DONGLE
You can build a dongle that plugs into the printer port.Purchase a 25 pin male D sub connector and solder insulated wires to the various pins as listed below. The pins are numbered on the connector
http://www.tilman.de/sonstiges/toshiba/dongle1.jpg this is a picture of the finished dongle


Wire the pins as follows :-1-5-10, 2-11, 3-17, 4-12, 6-16, 7-13, 8-14, 9-15
Plug the finished dongle in the printer port and power up the laptop. The password will be reset, go into the BIOS configuration to check the BIOS password, you may have to disable the BIOS password.

Anonymous

  • 263 Answers
  • Posted on Aug 09, 2011

SOURCE: Hello i have printer

Hello!
You can take a look in the Address Book. You will find there your user and password.
If you dont know how to see the address book ask your IT.
See you!

him001

Himanshu Mishra

  • 53 Answers
  • Posted on Aug 28, 2012

SOURCE: i ve problum scanner memory full error in nashuatec dsm 735

Reset and flash the scanner.

Brian Carson

  • 2 Answers
  • Posted on Jan 29, 2014

SOURCE: LG Washer wont start, no power

I HAVE A BEKO 42WLH530HID TV, AND WHEN I TURN IT ON THE STANDBY LIGHT COMES ON BUT NO PICTURE OR SOUND, I KNOW ITS 1, OFF 3 CIRCUT BOARDS BUT DON,T KNOW WHICH ONE, CAN ANYONE HELP ?

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Candy Bianca washing machine with unresponsive display.
Check all the connectors on the control board and display board. Undo, spray with switch cleaner and replace.
Read full answer
Dec 27, 2022 • Candy Washing Machines
0helpful
1answer

On my proform 680LTwhen I put the key in I get an FF display and nothing works
You must to the following:

Adjust the Sensor Reed, or optical sensor. by 1/8" or 3mms if see the diagram.

If after adjustment the problem persist. You must Test or measure the voltage for +5vdc to I.C.( EPROM, ROM, etc) , coming up from the Lower Board( Main Controller Motor Board).

Re-connect the flexible cord between Upper Board(Display) VS. Lower Board(Main Controller Motor Board) .
After you did that the Display Board is faulty or Main Controller Motor Board is faulty Replace.

Of course try to use the Dvoltmeter. very important.

sincerely.
Read full answer
Nov 22, 2011 • Proform 680 LT Treadmill
0helpful
1answer

Fitnex t60 display says prg bad, what does that mean and how can i repair it
1) You must test first the power supply for +5DC for I.Circuit( Including EPROM, ROM, etc)
2) Test the flexible cable between KeyPanel and display board, and clean.
3) Chechk the connector between Display Board with the lower board(Main Controller Motor)for loose connection, loose wire.
4) Test the transformer controller supplying the 12VCA, to the power supply at the Main Controller Board since this supply the +5vd to the Display Board.
Finally you must have Strong Conclusion if the problem is 1)Display Board faulty, 2) Power supply Faulty, 3) Transformer Controller Faulty 4) Main Controller Board Faulty.

For All test you must use Dvoltmeter.



sincerely.
E.CUADRA
MANAGUA, NICARAGUA.C.A
Read full answer
Nov 21, 2011 • Fitnex T60 Light Commercial Treadmill
0helpful
1answer

Hi I have problem with my photocopaier. Sharp ARM236. It shows Code: U2-40
U2-04 EPROM error
U2-11 Main counter error
U2-12 EPROM error

As you can see there are many U2 error codes. Needless to say, find your code and the replace the bad part. The battery is on the main board. The EPROM is on the main board.
If you find your code, replace the part and error still remains -- replace main board.
Read full answer
Aug 07, 2011 • Sharp AR-M237 Copier
1helpful
1answer

All the lights are lit up on this printer. Have installed a new toner cartridge and still can't get anything to work. When turned on, there is no noise at all coming from printer. Shouldn't there be a...
When all the lights come on when you power the printer it usually means there is a problem with ram or the eprom will not initialise. Remove any additional ram and see if that cures it. If not then the main circuit board will need to be replaced. However if you can get into download mode (unlikely) then try and update the firmware.
Read full answer
Apr 26, 2011 • Office Equipment & Supplies
5helpful
1answer

WD420, drying high heat, time saver and ON/OFF buttons are flashing, no function out of machine at all
this usually means that the main pcb has a corrupted eprom or eprom memory has been wiped... you either need a new pcb with eprom or a new board pre-programmed.

hotpoints terms for error

Setup error: check eeprom
F09
Flash
OFF
OFF
Flash
OFF
Read full answer
Dec 18, 2009 • Hotpoint Ariston Aquarius WD420 Front Load...
2helpful
1answer

I can't access dsm reset through fishfinder menu, it keeps saying no data source and I can't scroll down!
Check that there is power available at the DSM. Then verify that the DSM connector cable is correctly connected between the DSM and the C120. Finally, be sure that you have the most recent software version installed ( V 4.29). If all of that fails to bring back the DSM, try a factory reset. You accomplish this by holding down the first softkey while powering up the display. Hold the softkey until the reset countdown ends and the display begins to reboot. Be aware that a factory reset will delete any waypoints, routes, etc. so be sure to back upp anything important.
Read full answer
Sep 25, 2009 • Raymarine C120 System Pack C120 Raystar...
0helpful
1answer

XEROX WORKCENTRE M20 WHEN POWERING UP MACHINE IT WILL NOT COME OUT OF WARM UP MODE. FUSER IS HOT. MACHINE DISPLAY WILL SAY WARMING UP, MACHINE WILL CYCLE, SCANNER WILL MOVE , PRINTING WILL APPEAR ON...
what you want to do is this, turn the machine off. Remove the back cover. Then on the main board you should see a memory stick or 2 depending on the model.
Remove the memory sticks, then power up the machine with them out. Let it come to ready, then re install the memory sticks and power the machine back up to remove any software corruption.
Read full answer
Apr 08, 2009 • Xerox WorkCentre M20 All-In-One Laser...
0helpful
1answer

U2 PROBLEM blinking U2 and will not print
U2 RAM error
U2-00 EPROM error
U2-01 Counter error
U2-01 Memory back-up battery dead
U2-04 EPROM error
U2-11 Main counter error
U2-12 EPROM error

As you can see there are many U2 error codes. Needless to say, find your code and the replace the bad part. The battery is on the main board. The EPROM is on the main board.
If you find your code, replace the part and error still remains -- replace main board.
Read full answer
Feb 03, 2009 • Sharp AR-5316 Advanced Digital Imager...
0helpful
2answers

Main board dead
is the switch ok? Clean your Motherboard for dust too. CORRUPTED BIOS Reprogramming the BIOS depends on your motherboard Model. It should correspond to your BIOS Model. Download the Motherboard's BIOS file usually in a Zip file then the contents are .bin files. Then use the BIOS manufacturer's EPROM Programming tool. Which usually comes with a user manual or guide on how to's. Just follow its examples. Hope this helps ======================= If you are having trouble with Newly bought items save your self from headaches by returning them and demand a replacement or a refund! You may have purchased a reconditioned\repaired\factory defect product.
Read full answer
Sep 21, 2007 • MSI 915G Combo-FR Motherboard
Not finding what you are looking for?

View Most Popular

Office Equipment & Supplies

Related Question

Candy Bianca washing machine with unresponsive display.

  • Candy Washing Machines

63 views

Ask a Question

Usually answered in minutes!

Popular Questions

Interrupt button is flashing on my WorkCentre 3655 and the machine won't power up.

The Office Equipment & Supplies

Senville mini split unit displaying error code pc 03

The Office Equipment & Supplies

What is the fix for 59.C0 Error on Laserjet Pro 400 Color; M451dn

The Office Equipment & Supplies

Communication error occurred. Check the I/F cable connection and power of printer.

The Office Equipment & Supplies

I have a m20 microprojecter i got at an estate sell it says i need an activation code but they say it has no purchase history and cant provide the code how can i bypass it

The Office Equipment & Supplies

Check Out the Latest Printers Report
Check Out the Latest Printers Report

View all Fixya Reports

Top The Office Equipment & Supplies Experts

vince

Level 3 Expert

2530 Answers

littlewheel

Level 2 Expert

122 Answers

Jean Thiebaux

Level 2 Expert

164 Answers

Are you a The Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...