Question about American Standard Plumbing

1 Answer

How to remove and replace pull down hose and head in an american standard kitchen faucet?

Female connector to hold head on is stuck in faucet

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Download the BILT app and search for your faucet model. The icon is turquoise with a white nut ( as in nut and bolt).
It will show you step by step nearly everything under the sun. Hope that helps a bit.

Posted on Nov 09, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 171 Answers

SOURCE: kitchen spout leaks

Hi buffy9,

I'm Harvet the Master Plumber.

Your question is: You have an American Standard two faucet in my kitchen and the base of the spout leaks at the base. How do you remove it and replace the washers?

Are we talking about an American Standard two HANDLE faucet or one of the single handle models?

Thank you,
Harvey your Master Plumber

Posted on Oct 17, 2008

Bill Johnson

  • 297 Answers

SOURCE: how to replace sprout seal kit in american standard faucet ?

just pull straight up,wiggle back and forth,the o-rings are holding it on .

Posted on Jul 15, 2009

Bill Johnson

  • 297 Answers

SOURCE: American Standard Colony Soft gooseneck kitchen faucet leaks base

at the spout near the base is an echeion ring. turn this counterclock wise then pull up ring to expose the neck,pull spout straight up.this echeion cap holds on the spout to the base there are plastic parts inside so be careful when pulling apart.

Posted on Jul 22, 2009

Anonymous

  • 35 Answers

SOURCE: Grohe ladylux plus kitchen faucet leaks from

Yes,it sounds like you have to replace the hose.Follow the braided hose under your sink until you come across a yellow and black fitting . it is comparable to an air hose fitting quick disconnection. once that is pulled from the sink port,unscrew the spray head and pull the ose through the faucet body from above the sink

Posted on Feb 23, 2010

bryan farmer

  • 112 Answers

SOURCE: We are trying to replace a Grohe kitchen pull out

The universal hose will not work on certain model faucets,best bet contact manufacturer and they may provide you a new hose at little or no cost if you tell them you will put a different brand faucet in.

Posted on Jun 12, 2011

Testimonial: "Thanks, that is something I didn't consider. After much wrangling, he did get it loose and re-threaded it. It seems OK for now. Thank you for replyi"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a ten year old American Standard Reliant pullout kitchen faucet. It leaks from the body into the cabinet below the deck. I removed the cartridge but was unable to remove the internal body. The...


Hi, Ok I see your problem? LOL The feed lines for the faucet are too close together at the min. you must spread the lines ever so slightly not to over bend, just enough to get the head/bottom of the hose to pull up thru the top. Fun job: level 6 on a scale 1-10. Have at it !

Sep 06, 2013 | American Standard 4205.001.021 Reliant+...

3 Answers

American Standard Kitchen Faucet Low water flow


I had the same issue with an American Standard faucet that I installed new 6 months ago. The diverter can be the issue if you have a sprayer attachment. Try unscrewing the sprayer head from the hose it's attached to. Now run the water full pressure with the hose pointed into the sink, obviously :~). After running the water for about 1 minute, connect the sprayer head back onto the hose, make certain the flat rubber washer and ring gaskets are seated in their grooves properly, and tighten until you have no water leaking from the sprayer head/hose connection. Now try the water through the faucet. If the problem was a temporary diverter issue, your pressure should be fine now. Good luck

Oct 31, 2011 | American Standard Kitchen Faucet 6310 020...

1 Answer

Low water pressure


Remove the spray head and point the hose into the sink drain. Turn the faucet on. If you have good pressure, cal American Standard for a free replacement spray head.
If you still have low water pressure without the spray head, ask them for a new faucet cartridge.
After replacing the faucet cartridge, if you still have low water pressure you will need to ask for a new faucet, possibly free if yours is still under warranty.

Sep 07, 2010 | American Standard Kitchen Faucet 6310 020...

1 Answer

How do I remove the spray hose from the brass connector under the sink?


Hi,
On the side of the brass there should be a clip or a pin that you can pop off... a knife or screw driver will work to snap it out of there... then the hose will just pull down out of the fitting...

heatman101

Sep 03, 2010 | American Standard Kitchen Faucet 6310 020...

1 Answer

[email protected]


check hose to head connection ,i.e. spout.

Apr 14, 2010 | American Standard Kitchen Faucet 6310 020...

1 Answer

American standard kitchen faucet leaking


soak down with WD40 and try again use a bigger wrench they all come off i have not found any that i have not been able remove!

Jul 04, 2009 | American Standard Kitchen Faucet 6310 020...

1 Answer

How to replace sprout seal kit in american standard faucet ?


just pull straight up,wiggle back and forth,the o-rings are holding it on .

Jun 05, 2009 | American Standard 4275.550.002 ColonySoft...

1 Answer

Slow and nonexistent water flow.


Start by removing the spray head from the hose. Pull the spray head out and with a channel lock pliers unthread connection between the spray head and hose. BE CAREFUL not to let the hose fall back down into the faucet. With the hose directed down toward the sink test for volume by turning on the faucet. If you get a nice volume the problem is in the spray head. This is usually the case. Put the spray head back on then remove the aerator. It's the screen where the water comes out of the spray head. Clean out the assembly ( 3-4 parts). Reassemble and test.

Good luck, Phil

Dec 11, 2008 | American Standard Bath Faucet Ceramix...

2 Answers

Kitchen spout leaks


Hi buffy9,

I'm Harvet the Master Plumber.

Your question is: You have an American Standard two faucet in my kitchen and the base of the spout leaks at the base. How do you remove it and replace the washers?

Are we talking about an American Standard two HANDLE faucet or one of the single handle models?

Thank you,
Harvey your Master Plumber

Oct 16, 2008 | Plumbing

Not finding what you are looking for?
Plumbing Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top American Standard Plumbing Experts

Thomas F. Schneider

Level 3 Expert

2715 Answers

Donni Steen

Level 3 Expert

687 Answers

john h

Level 3 Expert

22486 Answers

Are you an American Standard Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...