Question about Measuring Tools & Sensors

2 Answers

I have a digital weather station. the outside sensor is not transmitting. The model no. is H10515/DCF. if still available can i purchase one?

Posted by pieter sonke on

Ad

2 Answers

STEVE SPAM REMOVER

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Measuring To... Master
  • 35,809 Answers

Replace the outside units batterys with lithium ones. bring it in and put it close to the indoor unit and let them pair. then put it back outside first..

Posted on Oct 28, 2019

Ad

ray gallant

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Measuring To... Master
  • 68,569 Answers

FIXYA WOULD NOT HAVE THIS INFORMATION TRY YOUR LOCAL RETAILER

Posted on Oct 28, 2019

Ad

5 Related Answers

Anonymous

  • 2 Answers

SOURCE: does not transmit. it has receive and weather

The PLL chip is burned out

Posted on Mar 14, 2009

goggomobil

  • 273 Answers

SOURCE: I have an Equity Weather

The wireless unit that transmits to the indoor unit is weather resistant, but not immersible. Even so, try to shield the transmitter from the sun and rain, if possible. When positioning the transmitter, keep in mind that direct sunlight may cause false readings and mounting it on heat-retaining materials (like brick) will show a higher temperature, even after sunset. Avoid mounting it anywhere near things that give off heat (air conditioner units, dark exterior walls, etc.).

LaCrosse has not yet uploaded the manual for this, but you may check later at:

equitybylacrosse.com/31215

Good luck from Detroit, MI.

Posted on Apr 29, 2011

Testimonial: "Thanks the information given was very helpful"

Ray Nardo

  • 1 Answer

SOURCE: Sharp Weather Station Model SPC344 The outside

After inserting the batteries, DO NOT set the time until the OUTSIDE temperature registers. That's the trick.

Posted on Nov 06, 2011

skychief2001

Stephen

  • 21873 Answers

SOURCE: Why does a 2008 dodge ram 5500 CUMMINS automatic Transmition get hot when i use my ac when the weather is hot outside

Its possible the radiator is not cooling enough to handle the engine and trans. Depending on where the aux cooler is for the trans, there may not be enough air flow thru the radiator. With the condenser in front of the radiator the ac produces extra heat the radiator has to overcome.

Posted on Aug 17, 2012

Tom Chichester

  • 56001 Answers

SOURCE: Weather station model 1531-3 outside readings never worked why

  • Incorrect batteries installed
  • Incorrect set up routine
  • Defective transmitter

Posted on Jan 10, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have the Atomic Clock model W86111. I had to change the batteries on the outside device. The clock outside temp just flashes 63.5 all the time. How do I make it sync to the device outside?


Remove all batteries from outdoor sensor and weather station.

Press one of the buttons on the weather station at least 20 times to clear all memory.

Verify that the weather station is blank before proceeding (there may be lines painted on
the screen that will show when power is removed).

Leave both units without power for 15 minutes (very important).

Insert fresh batteries into the clock.

Insert fresh batteries into the outdoor sensor.

Press the TX button on the outdoor sensor to transmit RF signal.

Keep the outdoor sensor 5-10 feet from the forecast station.

When RF connection is established, the temperature will appear on the station. Allow the
outdoor sensor and weather station to sit together for 15 minutes to establish a strong
connection.

Oct 14, 2017 | Home

1 Answer

The outside transmitter for my Lacross weather station, model WS-9080U-IT is not working. I replaced the batteries. How do I get it to transmit?


First remove the batteries and wait 5 minutes and then try again. If still no success, make sure that you are close enough to the sensor, take the sensor inside to the readout and see if it picks it up. If it does then there may be interference.

Dec 21, 2016 | Measuring Tools & Sensors

1 Answer

Why is there a red blinking light on outside sensor? This is only 2 weeks old and new batteries were put in then.


The red blinking light, I believe is indicating the outside sensor is transmitting the outside temperature data to main weather station unit.

Jun 19, 2015 | Measuring Tools & Sensors

2 Answers

Why my outside transmiter don't work


The first thing to do is bring it in close to the base and see if it works. Then use the process to reset it and then change the battery. All those things could impact the operation of it.

Apr 17, 2015 | Measuring Tools & Sensors

1 Answer

Rc sensor outside will not transmit 4-ld3091-t


Try physically taking your inside unit outside, and replacing the inside unit batteries as close as possible near the outside unit. Once the transmitter has found the signal, it should lock on and continue to work. Good luck.

Dec 08, 2014 | Measuring Tools & Sensors

1 Answer

My weather station is no longer recieving an outdoor temperature reading. The barometer is working fine, as is the indoor base station. Both were given new batteries at the same time, and the set up i


hi,


does the outside humidity working ?

if yes - the outside station is transmitting but the temperature sensor is faulty,
if no sensing is available from the outside station, it look like the outside station is faulty . (this is common because of extreme weather change.
notice that the pressure sense is done in the base station.
regards ,
Daniel
https://www.rylwy.com/

Nov 23, 2017 | Measuring Tools & Sensors

1 Answer

Next tech weather station is. Not w


Try taking the inside unit outside as close to the transmitting unit as possible for three minutes. The signal might lock on to the setting you want to receive.

Jul 01, 2014 | Acu-Rite Acurite Wireless Weather...

1 Answer

The sensor from my weather station is not registering outside temperature


I've had the same problem since I bought this unit 2+ years ago; when the outside temperature moves into the freezing zone, the sensor stops transmitting. I contacted Lacrosse-- all they could suggest was change the batteries. My solution: throw it in the trash!

Aug 05, 2012 | Bushnell Measuring Tools & Sensors

1 Answer

Cannot get the weather station model ws-916ou-it to show outside temperature


I have three of these WS-916OU-IT units. After a few years, the outside sensor just fails. You will get dashes and a "TR" low battery signal, even if the batteries are good
just buy another whole weather station (short money) and set both the old and new weather station unit to receive from the single new outdoor sensor.
To do this - just follow the procedure for a single sensor - that is - put the batteries in the new sensor - then within 30 seconds - put the batteries in all the weather stations - they will all pick up the same outdoor sensor.
I now have three units running off of one outdoor sensor.
Seems a bit silly, but it works.

Feb 27, 2012 | Measuring Tools & Sensors

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

18401 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

55995 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...