Question about Toshiba Televison & Video

Open Question

Why does my new Toshiba TDP-S35 lamp not turn on at all? Replaced it but can't turn it on. What should I do?

I had the old lamp on and after several warnings to replace it, it turned itself off. I replaced it, turned power back on but I get no light. Should I press any buttons before turning it on?

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 119 Answers

SOURCE: Projector does not turn ON

try removing the lamp, usually quite easy, you need to find the door for the lamp. lamps are customer replaceable, usually. If the lamp is bad you can usually see it damaged in the lamp. kind of like you might be able to see the broken filament in your normale house hold light bulb. good luck.

Posted on Dec 24, 2006

Ad

Lashawn Robinson

  • 1153 Answers

SOURCE: Replaced lamp and now can't get a picture

Hi Sally Jo, Unit powers on and works properly for a while then shuts off with a red lamp LED (lamp error). Suspect bad lamp part # 915P020010 2. Lamp enable line at J14 pin 6 does not switch to 5 volts after turn on, 12 and 5 volt supplies are good. Suspect the Light Engine part # 939P977010 3. At power on the lamp turns on and off three times and then the unit shuts down with a red lamp LED (lamp error). Replace the Light Engine part # 939P977010 4. Check for 12-volts DC at J-9 connector pin 4 on the Engine Driver PCB, if missing check for an open F9A09 on the Power PCB, if it is open replace F9A09 part # 283P127060 and the Light Engine part # 939P977010 5. Lamp enable line at connector J14 pin 6 on the Engine Driver PCB switches to 5 volts after turn on but does not go back to 0-volts (low) after 5 seconds, 12 and 5 volt supplies are good. Suspect the Light Engine part # 939P977010 6. Check for 5-volts DC at J-9 connector pin 1 and 2 on the Engine Driver PCB if missing replace the Power PCB part # 934C148001. Hope this helps!

Posted on Sep 18, 2007

Ad

Anonymous

  • 1 Answer

SOURCE: dell 2300mp projector

check this out...
http://www.ihatedell.net/forum/phpBB2/viewtopic,p,36316.html
have almost the same problem. lamp light turned on-->replaced the bulb, now when you turn it on tryies to boot and then the lamp light is on again (but the bulb is brand new).... and no light at all coming out of thing... I guess dell just don't know how to built projectors right way.... and theirs tech support guys are.... they just don't know about projectors more then manual

Posted on Jun 27, 2008

Anonymous

SOURCE: projector

Same problem

When i turn the projector on it only comes on four about a minute until the temp lights go amber and it turns off, the fan is working but the air coming out is a little warm. what if anything is making my projector overheat, or is it not heating at all?

Posted on Aug 07, 2008

rylee_smith

Rylee Smith

  • 8619 Answers

SOURCE: projector

Hi

If the fan is not working, the lamp will not fire. Kindly make sure that the panels are seated properly. Also chek if the outer cover is seated back 100% as if that is not seated back 100%, the unit will not work.

Posted on Mar 07, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced the lamp on Toshiba TDP T-45, now it won't turn on. Does it have a reset button or fuse?


Uninstall...reinstall.... Double check for touching wires then check fuse box for blown fuses

Jun 28, 2016 | Toshiba TDP-T45U DLP Projector

2 Answers

Mitsu hc3000 problem "red-green status light blinking and no input"


Heres what the manual says about REd / green lights

Unplug the power cord from the wall outlet and contact your dealer

And also this:

Check that the lens cap is removed.
It may take about one minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes
and then try again.
If the projector was turned off before the lamp was cooled down suf? ciently last time,
the fan may start rotating and the POWER button may not work after the power cord
is plugged. After the fan stops rotating, press the POWER button to turn back on the
POWER indicator.
Check that the intake vent is clean.
Set SCART INPUT in the FEATURE menu to OFF. (See page 25.)
Check that the lamp cover is closed. (See page 33.)
Check that the cables connected to the external devices are not broken.
When an extension cable is being used, replace it with the supplied cable for check. When
images are displayed correctly, add an RGB signal ampli? er to the extension cable.
Check the operation manual of the video device for its connection.

Mar 14, 2008 | Mitsubishi HC3000U Multimedia Projector

1 Answer

Projector tdp s9 lamp indicator turns yellow light, even when new bulb is replaced correctly


Once you replace the lamp you need to go into settings and reset the bulb hours back to zero. That will take care of your problem

Feb 14, 2015 | Toshiba TDP-S9 Multimedia Projector

1 Answer

Hi, There was a popping sound from my PLC-XL50, then the projector turned itself off. I noticed that rather the replace lamp light being lit, the warning light is on. Does this mean the lamp has died...


This is an indicator stating the lamp is bad and cannot power the projectors backlight. You should replace this prior to any additional powering of the unit.

Sep 22, 2011 | Sanyo PLC-XL50 Projector

2 Answers

JUST PUT NEW BULB IN A TOSHIBA TDP-S20 ON 2/18/11 . BOUGHT PROJECTOR IN 2004 USED UNTIL THE BULB HRS RAN OUT . BULB NEVER BROKE / BURST. ON START UP WITH THE NEW BULB IN MACHINE BOTH FAN AND LAMP LIGHTS...


Your new bulb is not lighting.
Check the connections are correct.
Have you also tried putting back old bulb to see if it works.



---


Please dont forget to vote this answer was helpful

Many thanks

------

Feb 18, 2011 | Toshiba TDP-S20U Multimedia Projector

1 Answer

It suddenly stoped playing clearly. i can see some extremelly pale picture.my lamp is around 2000 hrs the projector is a 2004 model toshiba TDP-D2.any ideas?thanks panos


You need a new lamp. You can purchase one at:

http://www.shopvsc.com/Toshiba-Replacement-Projector-Lamps-s/143603.htm?searching=Y&sort=7&cat=143603&show=50&page=1&f-TDP%20D2=143381

Oct 25, 2010 | Toshiba TDP-D2 Projector Lamp

2 Answers

Suddenly turned off without warning Sony KDS-50A2000


Hello,

All you need is to open the back cover of the television and check on for dry soldering at the power stage of the printed circuit board, also check for bulged capacitors, if found replace with same rating of voltages , but if otherwise Ur power supply board is dead, u know basic electronics’ and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get ur tv power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Hope this helout, Good luck....

Jul 11, 2010 | Sony KDS-50A2000 50" HDTV

1 Answer

My TDP-S35 suddenly went to showing only in black and white. Any ideas? It was working perfectly and in the middle of a class it lost all color.


if this is a DLP projector, take the cover off and check the colorwheel. It sound to me like you have lost the segments off the colorwheel.

May 17, 2010 | Toshiba TDP-S35 DLP Projector

Not finding what you are looking for?

Open Questions:

Televison & Video Logo

Related Topics:

66 views

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76573 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

matt martin
matt martin

Level 3 Expert

1258 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...