Question about Ricoh Office Equipment & Supplies

Open Question

Ricoh Aficio Mp C2050 error code sc491 what is the poblem

Posted by waruna hettiarachchi on

Ad

5 Related Answers

spinal

jeff heightchew

  • 287 Answers

SOURCE: Ricoh Aficio 1224c

Hello billboards,
SC 570 means that despite the fact that the the copier had been giving a "FUSER OIL LOW" prompt in the upper left hand corner of the display for quite some time, the prompt was ignored and now the oil is more than low it is empty. You will first need to aquire fusing oil for your machine.Typically it would be purchased from the same source you would aquire toner as it is something that is consumed as the copier is used similliar to toner. Once you have the oil you will need to replenish the copier's supply of oil. To do this you will need to access the back of the machine. Once you are at the back of the machine,look down to the lower right hand corner. You will see a small square panel with what I would describe as an oversized white plastic flathead screw that needs to be turned counterclockwise to release the small panel/cover. Once you remove the cover you will see a clear container witha black screw on cap. Unscrew it,and fill the container with the oil and stop filling when it reaches the neck of the container. Button everything back up and now you are halfway out of the woods. Now we go to the front of the machine. We need to reset the code. There is a yellow rectangular button above the nine key pad used to enter the number of copies you want. Now that you have located it, press it once and then press the "1" then the "0" then the "7" and then press the round red stop button and hold it down until the screen changes and beeps. At this point the display will have several blocks showing. One of the blocks will say "copier".Press the copier block. Now you will have a drop down menu to the left and several options across the top of the display. At the top,from left to right,the fourth box should say "SP DIRECT" and should actually already be highlighted. At this point,merely press "5810" on the keypad and then press the " # " pound sign. The pound sign means enter. At this point you should see a prompt that says something like "SC reset" and there will be a bar below the prompt that says "EXECUTE" .Press the execute button. This resets the code. But now you must turn the main power off (the red switch located next to your left knee on the front panel of the copier) and wait a few seconds. Now turn that switch back on and you should be good to go. I just reviewed my instructions and wanted to stress that the yellow button above the nine key pad says clear/stop. Just wanted to be more specific. I bet you have this problem whipped in no time! I hope this helps.Take care and good luck.And please feel free to let the folks at "FIX YA" know if I helped you. I don't get paid by them but I like the pats on the head . :-) ...........spinal.......

Posted on Apr 19, 2008

Ad
Bubbabear64

Tim Babcock

  • 2794 Answers

SOURCE: Error code SC305 for Photocopier Ricoh Aficio 1224c

Its a charge corona cleaning error. Try turning the power off, wait 10 seconds and turn it back on.

If that doesn't reset it, it could be the pcu, toner collected on the mechanism.

If turning it off and back on isn't fixing it, you should get a technician to look at it to see what the trouble is.

Posted on Jun 19, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: ricoh aficio 2022 error code sc542

1. Mode(Yellow Button)
2. 107
3. Press STOP Button for 3 second (RED Button)
4. Copy Sp
5. 5810#
6. Excute
7. Power Off
8. Power On


Posted on Feb 24, 2009

M2Tech1

Andy Bell

  • 313 Answers

SOURCE: error codes SC545 for Ricoh Aficio 1045

yes you may it refers to a temp error int eh fuser... you may have a faulty thermistor or thermo fuse.. if you go into teh service mode by presssing teh yellow clear butto and then press 107 and then hold down the stop button the sreen will change turn the machine off and turn on again see if the errpr goes if it does it could have been just a temp error if it warms up then comes back on again you will have to look at the fuser.. you can check the fuser by touching the casing and see if it is warm after you have turned the machine back on..if it is warm the error could just be due to a build up of toner on the thermistor.. if you know about machines you can take the fuser out by opening the front of the machine up look to top right where fuser is there is a screw under the blue dial on the fuser take that out the fuser slides out put it on some paper and on the right hand side is the thermistors held inby a small screw if you take them out you may see some build up of toner on the resistor carefully clean this off.. put back together and turn on .. hopefully it will run ok.. good luck A

Posted on Jun 26, 2009

Anonymous

  • 114 Answers

SOURCE: scanrouter v2 lite at ricoh aficio MP 4000

you dont need scanrouter for mp 4000

Posted on Mar 21, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is error code sc565?


If you wish to get some details; check the site linked here. Pull up older posts......
http://electro-medical.blogspot.com/

Jun 25, 2016 | Ricoh Compatible 4 Color Set Aficio MP...

1 Answer

How to fix colour position in ricoh c2050


tthe machine can do autocalibrattion,
see the video

Oct 05, 2015 | Ricoh Compatible 4 Color Set Aficio MP...

1 Answer

Ricoh mp 1600 error 194 ricoh mp 1600 error code 194 how do I solve the problem


Having problems finding your error code. Here is a complete list of all codes for your printer: http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=Ricoh&model=Aficio%20MP1600

I do find the error code for a different Ricoh model (Aficio 1018).
http://printcopy.info/?l=en&mod=free&chap=erc&brand=Ricoh&model=Aficio%201018

Please verify your model number and error code.

Apr 21, 2015 | Ricoh Aficio Mp-1600 Copier

1 Answer

I have an error on my gestetner mp c2030 with code sc222, please help me.


Problem with the yellow laser unit. Probably need a tech for that one.

May 20, 2014 | Ricoh Compatible 4 Color Set Aficio MP...

1 Answer

My Ricoh SPC811 DN shows always an error code SC491


hi
this error code is about "Cooling fan motor lock", we have 2 Reason for this code,1: Cooling fan motor defective or a loose
object is interfering with the fan and 2: Poor fan motor connector connection
please check them

Oct 06, 2013 | Ricoh Brand Aficio Spc811dn WASTE DISPOSAL...

1 Answer

2030 sc573 code


IT TELLS YOU THE TERMISTOR HAD TO BE REPLACED & LATER YOU TO HAD TO RESET THE MACHINE

Sep 14, 2013 | Ricoh Compatible 4 Color Set Aficio MP...

2 Answers

Sc491 error on ricoh MPC 3500


Sc 491 straight from manual

High voltage power: Drum/ development bias output error
An error signal is detected for 0.2 seconds when charging the drum or
development.
 High voltage leak
 Broken harness
 Defective drum unit or development unit
 Defective high voltage supply unit

1. Check or replace the harness.
2. Replace the drum unit or paper transfer unit.
3. Replace the high voltage supply unit.

Nov 16, 2009 | Ricoh Aficio CL3500N Laser Printer

Not finding what you are looking for?

Open Questions:

Office Equipment & Supplies Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

Bernard D'Souza

Level 2 Expert

164 Answers

Timothy Van Der...

Level 2 Expert

152 Answers

Cindy Wells

Level 3 Expert

6198 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...