Question about Building Materials

1 Answer

Our garage door opener is not working. The person who check it he said the problem is the chip board. Is there possibility to replace the chip board.

Posted by Jimlet Abengoza on


1 Answer

john h

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Master
  • 23,424 Answers

Buy a replacement

Posted on Oct 21, 2019


5 Related Answers


  • 244 Answers

SOURCE: garage door circuit board replacement

get instructions and program. I hate Genie

Posted on Jan 15, 2009



  • 318 Answers

SOURCE: Homelink Garage Door Opener works in-consistently on 99 Chrysler

Change the battery in your IN Car remote control.

Posted on Jan 16, 2009


  • 244 Answers

SOURCE: Need Replacement nutone garage door openers

unit must be ancient. try sears for a universal radio control set. if unit is as old as i think, i would toss it and get a new one. you will not be able to get any parts for this unit and it does not have safety beams.

Posted on Jan 28, 2009


  • 244 Answers

SOURCE: keypad garage door opener will not operate

what keypad are you using with new opener? Frequency has changed. can't use old one. you probably never needed to change things; just needed to follow proper coding procedures.

Posted on Jan 28, 2009

SOURCE: Just installed a new genie garage door opener.

Change the sensor and make sure the magnet comes close enough to activate it. Sometimes I have even changed the magnetic ones for real switches too.

Posted on Jan 31, 2010

Testimonial: "Thanks for the info. Interesting you mention a magnet. I don't see one unless its built into the carriage."

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Garage door opener

Check photo eyes. Shut off power to units and try again

Aug 21, 2016 | Building Materials

3 Answers


1st, try replacing the battery in the remote. If that doesn't work, you will need to replace the logic board on the opener, which is typical in the craftsman openers.

Oct 02, 2014 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Garage door send receive signal

Caution: do not use LED bulbs with garage door openers. They are a possible source of signal interference between the transmitter and receiver on the opener.

Mar 22, 2013 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

We have Craftsman garage door openers for both doors on our double car garage. The problem is with our keypad and our remotes in the cars. The keypad and car remotes work fine for one side of the garage,...

It sounds like the logic board has quit working on the one opener. If you have had lightning or power surges you might remove the logic board and check for loose, burnt or missing traces on the printed circuit.

Jul 12, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

I have a Craftsman 13953919 door opener. My garage door opens during the day when I am not home. The alarm company calls me to let me know, and the police have been by twice. Nothing is stolen, so I can...

Here are some things to check.

Look at the LED light next to the SMART/LEARN button on rear of the motor unit. You may need to remove a light lens cover in order to see it. If the light is flashing rapidly this means you have a stuck button on one of your remote controls. Take the batteries out of each remote control. When you remove the batteries from the bad remote, the light will stop flashing. This remote needs to be replaced.

If one of your neighbors remote controls is inadvertently programmed into your receiver, you door will open when their remote is activated. If this happens you will need to clear out your receiver and reprogram your remote controls. Press and hold the smart/learn button for 6 seconds or until you see the small LED light near the button turn itself off. If the above steps have been followed and the symptoms continue, there may be an electronic short in either the wall control button or the receiver logic board. In this case, remove the wall control wires from terminals 1 and 2 on the motor unit. Should the symptoms persist after the wires are removed, replace the receiver logic board. If the symptoms stop with the wall control wires removed from the motor unit, replace the wall control button, and the wires leading to the wall control button.

Apr 14, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

My controls will not open or close my garage door. The wired control works. I read that the logic board is bad. How much is the logic board and how hard is it to install. Is it better to just get another...

A new board is @ $86.00. Because I do not know your skill level I really cannot say whether it is easy or hard to install. I have replaced boards and I find it easy, but my brother would find it impossible. So it is subjective and you know your own skill level better than anyone else. I personally feel that it is not too complicated for a typical homeowner to do. In this economic time, some people have no choice and cannot spend the extra money for a new opener, but again I do not know your financial situation either. So the choice is yours, but if you can use a screwdriver and stand comfortably on a ladder, I would replace the board. I hope this helps and good luck!
Please remember to vote c5e7dfb.jpg and leave a testimonial. Thanks.

Nov 02, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Our remotes do not work when the garage door is closed, but they do work to shut the garage door when it is open. help

There are two possibilities here. One is the remotes batteries are weak and need to be replaced. The other is the receiver is going bad. If new batteries don't increase the range of the remotes then you will need to replace the logic board.

Aug 07, 2009 | Sears Craftsman LiftMaster Chamberlain...

Not finding what you are looking for?
Building Materials Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Building Materials Experts

Tom Chichester

Level 3 Expert

56023 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

ray gallant

Level 3 Expert

68633 Answers

Are you a Building Material Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides