Question about Audio Players & Recorders

Open Question

How to set zone on silicon projection atomic clock?

How to change time zone on silicon projection clock?

Posted by Ladonna Gober on

Ad

2 Related Answers

Chris Hauck

  • 1 Answer

SOURCE: silicon scientific atomic projection clock did no ...

I have one of these, and look for the manual on the 'Net every time DST changes, and eventually figure it out. Here's how: (1) Hold down the ALM/SET button until you get past the alarm setting and you see 24H or 12H. (2) Step through the settings by pushing the ALM/SET button, changing each as desired by pressing the +/CYCLE button. Eventually you'll wind up with the time zone indication flashing (it's really tiny, and appears just below the time indication). Press the +/CYCLE until you get to the desired time zone. (3) After the screen quits flashing, press the -/DST button to get the desired setting. I hope this helps, and that I can find this post again next time change!

Posted on Nov 09, 2011

Ad
emissionwiz

Marvin

  • 85239 Answers

SOURCE: How can I set the time zone on a Silicon Scientific atomic projection clock.

Try this Press the bottom left button thru the alarm sets, till you get to a -5 (ET) / -6 (CT) / -7 (MT) / -8 (PT). Then, press the upper left MODE button once. Now the -5 will flash, allowing a change. If you just went EAST you need to press the bottom right button once [ex: MT to CT - go from -7 to -6] If you went WEST, press the top right button once [ex: ETt0CT-gofrom-5to-6]

Posted on Nov 20, 2016

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I set the time zone on a Silicon Scientific atomic projection clock.


Try this Press the bottom left button thru the alarm sets, till you get to a -5 (ET) / -6 (CT) / -7 (MT) / -8 (PT). Then, press the upper left MODE button once. Now the -5 will flash, allowing a change. If you just went EAST you need to press the bottom right button once [ex: MT to CT - go from -7 to -6] If you went WEST, press the top right button once [ex: ETt0CT-gofrom-5to-6]

Nov 20, 2016 | Home

1 Answer

Change time zones


Hold down the + button on front of unit until the time zone moves.Then let go when it reaches the correct time zone.

Jan 26, 2014 | Hammacher Schlemmer The R2-D2 Projection...

2 Answers

My Hammacher Schlemmer Projection Alarm Clock and Weather Monitor will not project the outside temp. It only projects the inside temp. How do I change? Also, can't change the time zone.


No solution but to return it...very annoying product but yet I like the projected display, very sharp and bright. The replacement was much better, it loses connection with outside transmitter often..but occasionally we see the outside temp

Dec 28, 2013 | Hammacher Schlemmer The Projection Alarm...

1 Answer

It only shows et time when I hold down the button to change time zones it will not go to pt when I remove batteries and start over...I hate it.


Instructions...

you have to release the Mode/Min button after 3 seconds.

http://www.klockit.com/pdfs/87214.pdf

"TIME ZONE SETTING

1. Hold down the "MODE/MIN" button for 3 seconds, the time will flash in the Time LCD.

2. Press and release the "SNOOZE" button to advance to the time zone selection.
3. In the indoor temperature/humidity section of the LCD the time zone will flash."

Jan 08, 2011 | La Crosse Lacrosse WT-5120U-BP Projection...

2 Answers

Silicon scientific atomic projection clock did no reset for daylight saving. Help


I have one of these, and look for the manual on the 'Net every time DST changes, and eventually figure it out. Here's how: (1) Hold down the ALM/SET button until you get past the alarm setting and you see 24H or 12H. (2) Step through the settings by pushing the ALM/SET button, changing each as desired by pressing the +/CYCLE button. Eventually you'll wind up with the time zone indication flashing (it's really tiny, and appears just below the time indication). Press the +/CYCLE until you get to the desired time zone. (3) After the screen quits flashing, press the -/DST button to get the desired setting. I hope this helps, and that I can find this post again next time change!

May 19, 2010 | Watches

1 Answer

Silicon Scientific Radio Controled Watch


how to change hour number for setting clock back

Feb 05, 2010 | Watches

1 Answer

Can't figure out how to set the time zone


I just pressed and held for about 3 to 5 seconds the button with the +/- on the bottom of the clock and until it showed the part of the US that I was in.

May 18, 2009 | Honeywell RC182WR Atomic Alarm Clock - Red

1 Answer

Changing the time


you can go to http://www2.oregonscientific.com/assets/manuals2/bar338pa.pdf to see or print the user's manual.

If you don't want to get the manual, here's what you do to fix it. . . . .
*note: you need to do this anytime you change the batteries.

1) open the battery cover
2) on the left side you'll see 3 little buttons labeled a)zone, b)C/F c)reset
3) push the reset
4)push the zone button until your time zone is highlighted on the front display
5) look at the front display & if you see a blinking "radio signal" icon at upper left of time numerals
don't do anything else. The time, date, etc. will automatically synchronize your clock with the US Atomic Clock. This could take up to 10 minutes. As long as the "radio signal" icon is blinking, it's working on it. When the icon doesnt' blink, it's set. Cool, huh?
6) if the area you live in can't receive the signal from the Atomic Clock, instead of a blinking "radio signal", you'll see just a bare antennae. Since you probably set your clock manually, that's what it shows now before you do anything.
7) after you push reset & set the time zone do NOT touch any other buttons to set anything!!! (I know it's difficult to leave things alone, but just sit on your hands). Pushing the "clock" button or the up & down arrows will stop the radio signal & change to manual functions. Look at the signal icon mentioned in 5) and 6) above. If you only have the bare antennae icon. . . . . go ahead & set the time/date yourself. You have no signal.

Enjoy your clock!
debkresh

Jan 25, 2009 | Oregon Scientific FM Weather Projection...

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

 Grubhead
Grubhead

Level 3 Expert

5700 Answers

The Knight
The Knight

Level 3 Expert

76455 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...