Question about Kenmore Ovens

Open Question

My Kenmore oven shows error code F-1. Model # 790.47853406.

We had a power outage and after resetting clock time it won't respond to "Bake". Instead the error code shows. What should I do?

Posted by on

Ad

5 Suggested Answers

Anonymous

  • 159 Answers

SOURCE: Dacor Oven Won;t Heat

power surges can short out the electonics in appliances. If you can locate where the tech sheet is and I would say its behind the control panel on top, look at the wiring diagram and see if there are any replaceable fuse's. Or a resetable fuse for the heating element. If not check to see if power is getting to the main control bord. If there is power there you may need to replace the control.

Posted on Jul 20, 2007

Ad

Anonymous

  • 1 Answer

SOURCE: kenmore oven touch panel error codes f1 f3 f5 f7, oven failure

I had the same problem. It occurred when it was in a cleaning cycling. I fot the F3 Fasult and also the door remained locked. I let it cool down overnight and killed the power at the circuit breaker. I turned the power on and got a F3 alarm and the door remained locked. I took our the screws holding the control panel and pull it out far enough to give me access to the locking mechanisim. I took out the screw holding the locking latch to the motor. With the latch loose, iwas able to get move it out of the door lock. With the door now open I was able to get to the temperature sensor with was held with two sheet mmetal screws. The screw were impossible to get out, so I ground off the heads with a Dremel tool. I couldn't get the sensor wires out. So I pulled the unit out to get at the back sde. I cut the old sensor wires and was able to get in the hole to remove the screws with a pair of needle nose pliers. I installed a new sensor and with wire nuts attached the sensor wires to the computer wires. Make sure that you work the insulation in the hole to plug it back up. Put the oven back in and installed the sensor in the oven with two small sheet metal screws. . refasten the locking latch to the locking latch motor. turn on the power and everything was fine. I ohmmed out the old sensor and it was 180 ohms at room temperature. The replacement checked out at a 1000 ohms in accordance with the schematic for the control. By the way, the schematic was neatly folded on the control panel when I removed it I used a Whirlpool sensor Part No. 12001656 which was half the price of a Kenmore sensor. +

Posted on Oct 24, 2008

Ad

Anonymous

  • 5 Answers

SOURCE: stove-top works, oven showing all 888888 across the screen

You're stove must be perfectly fine, but the thing displaying all those options may have a problem. Try to get this fixed as soon as possible.

Posted on Feb 15, 2009

erica graber

  • 530 Answers

SOURCE: 665.95802000 f1 - E 1 error code

take the consol off you will find the tech sheet with all the codes. make sure you turn your power off first.

Posted on Dec 23, 2009

SOURCE: I have a Kenmore Ultra Bake Stove, we had a power

PF is usually power failure.
If "PF" appears at any other time, a power failure occurred. To remove "PF"and to reset the clock, press STOP/CLEAR.

Unplug the unit for half an hour or so to see if it will reset.
If not try to get into the diagnostics so you can see if there is a stored
error code

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a brand new Viking french door oven...Went to set it at 450 on bake setting and got an F02 error code. How do I fix this?


Fault F02 is indicating an overheat fault- service manual says to replace main electronic control board.
Sometimes switching off at wall will clear the fault.
However, switching off at wall will reset the clock- you need to set the time before the oven will work-press middle button until small triangle is next to clock icon, set time using temperature dial. Once clock has ben set, try using oven to see if F02 fault reappears. Good luck!!

Oct 05, 2017 | Viking Ovens

2 Answers

Thermador C302U error code


most of error codes disappear when a hard reset is done.

did u try a hard reset first?

Jun 28, 2008 | Thermador C302U Electric Double Oven

1 Answer

When we reset the clock after a power outage, the clock runs fast now almost a minute in 30 seconds. Bosch HBL5750


Advise manufacturer; may give you a warranty on this part even after it has expired because of nature of the problem.

Mar 08, 2015 | Bosch HBL5750UC Electric Oven

1 Answer

Wolf ovens getting err message after power outage


I had a Wolf 30F wall oven with a similar problem
after power outage. It wouldnt stop beeping with error message related
to temperature control. My solution was to turn power of at circuit
panel, then reset by pressing and holding the clear button for 5
seconds.

Also note: in my case I had to close the display
before switching the panel off. When I tried to the reset process with
the panel showing, it wouldn\'t reset.



To reset other
various parts of the control panel Instructions said:



Time-of-Day Clock

Immediately after the oven is installed, set
the 12-hour clock to the current time of day. It may need to be reset
after a prolonged power failure. The clock is visible on the control
panel during all modes. If the upper oven timer is set, the clock will
not be visible in the upper oven control panel display.



SETTING CLOCK

1) Touch CLOCK.

2) Touch number pads to
set current time of day.

3) Touch CLOCK or ENTER to start
clock.



24-HOUR CLOCK

The time-of-day clock can be
changed from a 12-hour clock to a 24-hour clock. After the clock has
been set, touch TEMPERATURE for three seconds, touch CLOCK, and then
touch ENTER. Follow the same sequence to change back to the standard
12-hour clock setting.



Fahrenheit to Celsius

The
oven can be changed from Fahrenheit (°F) temperature to Celsius
(°C).

Oct 26, 2012 | Wolf Range Ovens

1 Answer

I have a Kenmore Ultra Bake Stove, we had a power outage and neither the oven nor burners works. The code on top reads PF 5Ab. What can i do to reset the stove?


PF is usually power failure.
If "PF" appears at any other time, a power failure occurred. To remove "PF"and to reset the clock, press STOP/CLEAR.

Unplug the unit for half an hour or so to see if it will reset.
If not try to get into the diagnostics so you can see if there is a stored
error code

Feb 15, 2010 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

Indicator light says ''pf''


"PF" CODE USUALLY INDICATES A POWER FAILURE CLEAR CONTROL PANEL---RESET, CLOCK, OR TIMERS AND SET TO BAKE 350' IF EVERYTHING RESPONDS O.K. YOUR LIGHTS MAY HAVE BLINKED OR SOME OTHER POWER INTERUPTION

Jun 24, 2009 | Ovens

1 Answer

Display is in LOC but door is not locked. Can't set temp. to bake


check if u can find any reset procedure.

alsio u can let it with no power for 30mi that will reset it Int.Memory.

Feb 16, 2009 | Whirlpool RBS275PD Electric Single Oven

1 Answer

Stove-top works, oven showing all 888888 across the screen


You're stove must be perfectly fine, but the thing displaying all those options may have a problem. Try to get this fixed as soon as possible.

Jan 31, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

4 Answers

Erroe code 5ab


According to the manual, this mode is SAB and not 5AB. SAB stands for sabath mode and lasts for 72 hours. The mode may be canceled by holding in the clock button for 3 seconds. This mode was activated by holding in the clock button for 3 seconds. My wife did the same thing when resetting the clock for daylight savings time this year. Resetting the power does not reset SAB mode.

Nov 21, 2007 | Amana AOCS3040 Electric Single Oven

1 Answer

Dacor Oven Won;t Heat


power surges can short out the electonics in appliances. If you can locate where the tech sheet is and I would say its behind the control panel on top, look at the wiring diagram and see if there are any replaceable fuse's. Or a resetable fuse for the heating element. If not check to see if power is getting to the main control bord. If there is power there you may need to replace the control.

Jul 19, 2007 | Dacor ECS130 Epicure Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Ovens Experts

Brad Brown

Level 3 Expert

18166 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Kenmore Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...